| LOST JEEPS http://www.lostjeeps.com/forum/phpBB3/ |
|
| Help - Part numbers for Bushes Rear A frame http://www.lostjeeps.com/forum/phpBB3/viewtopic.php?f=3&t=65457 |
Page 1 of 1 |
| Author: | Pippobug [ Fri Feb 24, 2012 10:17 am ] |
| Post subject: | Help - Part numbers for Bushes Rear A frame |
Hi, can anyone help me with the correct part number for the Bushes for the rear suspention A Frame? I need to replace them Looking for the 2 bushes that hold the Rear A frame and the part number for the main central bush that connects to the rear axel. My KJ is a 2003 ( actual built 10/2002). Thank you, Fil. |
|
| Author: | tommudd [ Fri Feb 24, 2012 10:21 am ] |
| Post subject: | Re: Help - Part numbers for Bushes Rear A frame |
For the Tri-link try # 52088425 for the front two Ball Joint in the rear is 52088647AB |
|
| Author: | Pippobug [ Fri Feb 24, 2012 10:30 am ] |
| Post subject: | Re: Help - Part numbers for Bushes Rear A frame |
Tom, Thank you for the information. Fil. |
|
| Author: | Pippobug [ Fri Mar 02, 2012 10:39 am ] |
| Post subject: | Re: Help -Part numbers for Bushes Rear A frame-Now Popping N |
Hi, A bit of help. I got the parts and fittend them, but now I have a popping noise from the back. I think it might be the center bush connected to the back differential that keeps popping out as it's a bit too streched. I am lifed and sitting at 22 inc at the back, set up is OME948 & OME132L + 2 top isolator each side. What do I need to do to make it stop? I have seen Jeeping by Al sells a drop link for the back axel for 4 inc lift, see http://jeepinbyal.com/prod-Link_Extension-463.aspx, would this solve the problem? Fil. |
|
| Author: | tommudd [ Fri Mar 02, 2012 1:39 pm ] |
| Post subject: | Re: Help - Part numbers for Bushes Rear A frame |
Are you sure you have them in good and solid? I'm at least an inch higher than you are and no popping or anything |
|
| Author: | Pippobug [ Fri Mar 02, 2012 2:04 pm ] |
| Post subject: | Re: Help - Part numbers for Bushes Rear A frame |
Tom, Yes, I have checked, but might go and check again and make double sure. I take it you have the standard A frame at the back, that UCA from JBA would help so not to have the boll joint at such an angle? Fil. |
|
| Author: | Lancer [ Sat Mar 03, 2012 10:34 am ] |
| Post subject: | Re: Help - Part numbers for Bushes Rear A frame |
Fil - if you are thinking about that link extension, I'd read this before buying it http://www.ausjeepoffroad.com/forum/sho ... p?t=112902 If you are looking at the complete replacement from JbA then firstly, it involves welding onto the top of the rear diff, and secondly, some of the joints used MAY not be legal under the construction and use regulations over here. |
|
| Author: | Pippobug [ Sat Mar 03, 2012 11:01 am ] |
| Post subject: | Re: Help - Part numbers for Bushes Rear A frame |
Lancer, Thank you for your post. Looks like the popping noise has stopped so I won't be looking to add the JBA lift ball joint. Maybe if i decide to add more lift, then i will reconsider maybe. Fil |
|
| Page 1 of 1 | All times are UTC - 5 hours [ DST ] |
| Powered by phpBB © 2000, 2002, 2005, 2007 phpBB Group http://www.phpbb.com/ |
|