LOST JEEPS
http://www.lostjeeps.com/forum/phpBB3/

Ironman Lift install/comments/M&G
http://www.lostjeeps.com/forum/phpBB3/viewtopic.php?f=3&t=72094		 Page 1 of 2
Author:  tommudd [ Sun Oct 21, 2012 12:38 pm ]
Post subject:  Ironman Lift install/comments/M&G
I got one of the first Ironman lifts when Marlin (JBA) received them to test out.
I loved the ride right away, smoother ride than what I have in a way, handling is great, overall a great alternative to the OME setup. I ran the fronts for a while and the rear for quite a while longer checking them out.
Due to the extra weight of mine I went back to my setup and yesterday we installed the Ironman lift on 501s KJ for even more long term testing / evaulation.
Few shots of his, with top plate and 3 ring clevis in the front, 2 extra upper iso's in the rear
He's only driven it about 25 miles so far around here last evening and today but loves the ride so far. He just left for home and will put another 170 miles on this afternoon.
Image
Image
Image
comparing to mine
Image
couple of the others who were at the M&G / Lift install
Image
Image
Author:  dieselenthusiast [ Sun Oct 21, 2012 10:50 pm ]
Post subject:  Re: Ironman Lift install/comments/M&G
Tom, are you saying that the Ironman lift doesn't hold the extra weight of the ARB bumper as well the OME HD coils?
Author:  tommudd [ Sun Oct 21, 2012 11:13 pm ]
Post subject:  Re: Ironman Lift install/comments/M&G
No I didn't think I said that :?
Author:  dieselenthusiast [ Sun Oct 21, 2012 11:16 pm ]
Post subject:  Re: Ironman Lift install/comments/M&G
tommudd wrote:
No I didn't think I said that :?


You said, "Due to the extra weight of mine I went back to my setup..."
Author:  TwoBobsKJ [ Mon Oct 22, 2012 9:32 am ]
Post subject:  Re: Ironman Lift install/comments/M&G
dieselenthusiast wrote:
tommudd wrote:
No I didn't think I said that :?


You said, "Due to the extra weight of mine I went back to my setup..."


The Ironman won't lift the KJ as much as an OME - so add the weight of armor, ARB up front, etc. and it will not be at the same height as an OME spring setup. For example, the OME rear spring is about 2 inches taller than the Ironman when they're sitting on the garage floor. So the OME starts out that much higher in the rear though it compresses faster due to the linear spring rate. But still, the OME will be a tad higher to start with. Add in the above-mentioned items plus Tom's "garage-in-the-trunk" that he carries around all the time and those rear springs are compressed pretty quickly. If I remember correctly Tom had to run 3 rear upper iso's with the Ironman to get the height where it needed to be vs. 2 upper iso's with the OME springs.

Nothing wrong at all with the Ironman - great setup as you can see on 501's rig.

Bob
Author:  tommudd [ Mon Oct 22, 2012 9:38 am ]
Post subject:  Re: Ironman Lift install/comments/M&G
Ironman will provide the same amount of lift
Currently Daryl is sitting with a true 4 inches of lift in the front, ( middle of wheel to bottom of the flare) and this is after I ran the setup for a few hundred miles and now he has over 200 on them

I should of included I swapped them out also due to getting it ready to go to the Butler Jeep Festival and several road trips coming up. Didn't have time to fully explore all of the options I could of done. Daryl now will though
Author:  dieselenthusiast [ Tue Oct 23, 2012 8:48 am ]
Post subject:  Re: Ironman Lift install/comments/M&G
OME has the Medium Duty Springs, Heavy Duty Springs and the CRD springs. Three different spring rates for 3 different applications is what makes OME a good selection for those who need the flexibility. It would be interesting to see how the Ironman would handle an ARB bumper and winch after 10,000 miles of driving.
Author:  STINGN [ Tue Oct 23, 2012 12:08 pm ]
Post subject:  Re: Ironman Lift install/comments/M&G
my heavy duty OME springs have taken a beating with the ARB and xrc8...thinking about adding synthetic to the winch and adding the CRD coils...
Author:  dieselenthusiast [ Tue Oct 23, 2012 12:56 pm ]
Post subject:  Re: Ironman Lift install/comments/M&G
STINGN wrote:
my heavy duty OME springs have taken a beating with the ARB and xrc8...thinking about adding synthetic to the winch and adding the CRD coils...


I think that OME CRD coils are the best setup with the ARB/winch combo. And synthetic rope is the way to go.
Author:  tommudd [ Tue Oct 23, 2012 2:54 pm ]
Post subject:  Re: Ironman Lift install/comments/M&G
BEST would be a front coil with about 450-460 spring rate for those with ARB/winch etc
400 is not quite enough over the long run, 500 is a little bit too much
but thats just from my experience
Author:  501 [ Mon Nov 19, 2012 1:54 pm ]
Post subject:  Re: Ironman Lift install/comments/M&G
With around 1000 miles on the new lift, I'm sitting at:

FD = 22 3/4"
FP = 23"
RD = 21 3/4"
RP = 22"
Author:  TwoBobsKJ [ Mon Nov 19, 2012 9:30 pm ]
Post subject:  Re: Ironman Lift install/comments/M&G
Looks good, Daryl.

How about that dang driver's side droop...? :shock:

Bob
Author:  tommudd [ Mon Nov 19, 2012 9:33 pm ]
Post subject:  Re: Ironman Lift install/comments/M&G
TwoBobsKJ wrote:
Looks good, Daryl.

How about that dang driver's side droop...? :shock:

Bob


Going to start doing all of them like I do mine
1/8 to 1/4 higher on the drivers side from the get go :ROTFL:
Author:  501 [ Tue Nov 20, 2012 12:55 am ]
Post subject:  Re: Ironman Lift install/comments/M&G
tommudd wrote:

Going to start doing all of them like I do mine
1/8 to 1/4 higher on the drivers side from the get go :ROTFL:


I might cut out one of the conduit nuts from the passenger side front, that should even the front out.
Author:  501 [ Tue Nov 20, 2012 1:10 am ]
Post subject:  Re: Ironman Lift install/comments/M&G
TwoBobsKJ wrote:
Looks good, Daryl.

How about that dang driver's side droop...? :shock:

Bob


Probably not the jeeps fault I have been gaining weight lately! :ROTFL:

(Thought I'd say it before Hart did!)
Author:  matthewcrd [ Fri Nov 23, 2012 1:09 pm ]
Post subject:  Re: Ironman Lift install/comments/M&G
Hey tom so if your where to do a stock crd.... What would you go with? Ome or iron man amd what would you do to level it off.... I dont plan on a arb or anything just stock but i want it level and lift as i live in el paso n less weight is good in sand out here
Author:  jslibby [ Fri Dec 07, 2012 1:49 pm ]
Post subject:  Re: Ironman Lift install/comments/M&G
How much was the lift.

I love ironman I had them overseas so good
Author:  tommudd [ Fri Dec 07, 2012 2:15 pm ]
Post subject:  Re: Ironman Lift install/comments/M&G
matthewcrd wrote:
Hey tom so if your where to do a stock crd.... What would you go with? Ome or iron man amd what would you do to level it off.... I dont plan on a arb or anything just stock but i want it level and lift as i live in el paso n less weight is good in sand out here


For a CRD I'd do OME springs and shocks 790/948s
For some reason that combo holds up better in the long haul
Some have ran the 927s BUT they are rated at 400 where as stock CRD are 410
790s of course are 500
Author:  tommudd [ Fri Dec 07, 2012 2:17 pm ]
Post subject:  Re: Ironman Lift install/comments/M&G
jslibby wrote:
How much was the lift.

I love ironman I had them overseas so good


The Ironman ??
If so unless price has changed in the past few days four springs / shocks are 650 or so
of course add in top plate/ extra isos/ bumpstops if you want more lift, etc and you add in another 100 easy enough

Marlin has everything on his site. he even has a new site coming up soon thats easier to search for parts
Author:  fortx4 KJ [ Mon Dec 24, 2012 8:10 am ]
Post subject:  Re: Ironman Lift install/comments/M&G
I noticed that the coils are bunched real tight. Do you hear clanging of the springs up front?
Page 1 of 2 All times are UTC - 5 hours [ DST ]
Powered by phpBB © 2000, 2002, 2005, 2007 phpBB Group
http://www.phpbb.com/