LOST JEEPS :: View topic

I'd like to suggest that you use polyurethane windshield sealant. you won't use much, but it will seal perfectly and never have an issue. You would do well to put sealant over the hole before inserting the nutcert and clamping it down, then using it again when you run the bolts in.

When I did this, I put two bolts in from underneath with sealant to hang it by, and it would have been ideal to do this on all in case I ever need to remove it.

Author:	fish1 [ Sun Feb 24, 2013 6:16 pm ]
Post subject:	Roof Lightbar
I bought the factory light bar to install on my 05 lib could someone tell me what size an type of nutsert i need ? A pic would be great. Thanks

Author:	teckman02 [ Sun Feb 24, 2013 6:20 pm ]
Post subject:	Re: Roof Lightbar
everything needed to know about installing one right here http://www.ifsjeepers.com/phpBB3/viewtopic.php?f=24&t=38 at the same time i should know this because i just installed one on my WJ a little over a month and a half ago

Author:	teckman02 [ Sun Feb 24, 2013 6:23 pm ]
Post subject:	Re: Roof Lightbar
also you can never use enough RTV on your drilled holes in the roof

Author:	fish1 [ Sun Feb 24, 2013 6:36 pm ]
Post subject:	Re: Roof Lightbar
Thank you very much

Author:	JeepCoMj [ Mon Feb 25, 2013 10:02 pm ]
Post subject:	Re: Roof Lightbar
I'd like to suggest that you use polyurethane windshield sealant. you won't use much, but it will seal perfectly and never have an issue. You would do well to put sealant over the hole before inserting the nutcert and clamping it down, then using it again when you run the bolts in. When I did this, I put two bolts in from underneath with sealant to hang it by, and it would have been ideal to do this on all in case I ever need to remove it.

LOST JEEPS http://www.lostjeeps.com/forum/phpBB3/

Roof Lightbar http://www.lostjeeps.com/forum/phpBB3/viewtopic.php?f=3&t=74288	Page 1 of 1

Author:	teckman02 [ Mon Feb 25, 2013 10:11 pm ]
Post subject:	Re: Roof Lightbar
JeepCoMj wrote: I'd like to suggest that you use polyurethane windshield sealant. you won't use much, but it will seal perfectly and never have an issue. You would do well to put sealant over the hole before inserting the nutcert and clamping it down, then using it again when you run the bolts in. When I did this, I put two bolts in from underneath with sealant to hang it by, and it would have been ideal to do this on all in case I ever need to remove it. that is what i did when i installed one on my WJ

Author:	fish1 [ Tue Feb 26, 2013 12:49 pm ]
Post subject:	Re: Roof Lightbar
Did you just seal bolt holes ? does the base of the light bar need any sealant where it contacts the roof?

Author:	teckman02 [ Tue Feb 26, 2013 1:38 pm ]
Post subject:	Re: Roof Lightbar
fish1 wrote: Did you just seal bolt holes ? does the base of the light bar need any sealant where it contacts the roof? i used sealant on the nutcert's and the on bolt holes before i screwed then in and the hole where the wiring gromit is at. there is no need to put sealant on between the roof and light bar

Author:	JeepCoMj [ Tue Feb 26, 2013 4:15 pm ]
Post subject:	Re: Roof Lightbar
What he said.

Author:	fish1 [ Tue Feb 26, 2013 4:42 pm ]
Post subject:	Re: Roof Lightbar
Thanks again

Page 1 of 1	All times are UTC - 5 hours [ DST ]
Powered by phpBB © 2000, 2002, 2005, 2007 phpBB Group http://www.phpbb.com/