LOST JEEPS
http://www.lostjeeps.com/forum/phpBB3/

Anyone know the torque specs for...
http://www.lostjeeps.com/forum/phpBB3/viewtopic.php?f=3&t=74873		 Page 1 of 1
Author:  joejeeper420 [ Wed Apr 10, 2013 8:34 pm ]
Post subject:  Anyone know the torque specs for...
The engine and transmission mounts?
Author:  VAhlene [ Wed Apr 10, 2013 11:39 pm ]
Post subject:  Re: Anyone know the torque specs for...
bolt that attach to block? or bolt from mount to frame?
Found this using google hopefully that might help ya,
http://www.justanswer.com/jeep/1y8yy-looking-torque-specs-jeep-liberty-engine-3-7l.html
Author:  VAhlene [ Wed Apr 10, 2013 11:44 pm ]
Post subject:  Re: Anyone know the torque specs for...
also found this....
http://www.lostjeeps.com/forum/phpBB3/viewtopic.php?f=5&t=49882&hilit=engine+mounts

a little ways down the page there is a post that has a bunch of torque specs on the engine mounts and bolts it's for a crd but not sure if there is a difference in the torque values..
Author:  joejeeper420 [ Thu Apr 11, 2013 12:01 am ]
Post subject:  Re: Anyone know the torque specs for...
I actually found those... Wasn't sure if the values were the same as the 06, because I have an 02 and I have the 45rfe... And I know we have completely different mounts than the CRD. I always try to use the power of google before I ask a q? Unless I'm in a pinch for time! While I'm here I might as well ask another q? LoL... My new mounts have some open aired gaps in the rubber of the center of the mounts... Is that normal? They look brand new besides... Just trying to make sure I didn't get blems or something...
Author:  VAhlene [ Thu Apr 11, 2013 7:23 pm ]
Post subject:  Re: Anyone know the torque specs for...
joejeeper420 wrote:
I actually found those... Wasn't sure if the values were the same as the 06, because I have an 02 and I have the 45rfe... And I know we have completely different mounts than the CRD. I always try to use the power of google before I ask a q? Unless I'm in a pinch for time! While I'm here I might as well ask another q? LoL... My new mounts have some open aired gaps in the rubber of the center of the mounts... Is that normal? They look brand new besides... Just trying to make sure I didn't get blems or something...


Sorry I can't be of more help not sure if the mounts should have those aired gaps in the rubber, my guess would be to call a good Jeep dealership and see if they could shed some light on the situation or maybe someone else on here will chime in, best of luck!
Author:  TwoBobsKJ [ Thu Apr 11, 2013 9:19 pm ]
Post subject:  Re: Anyone know the torque specs for...
joejeeper420 wrote:
I actually found those... Wasn't sure if the values were the same as the 06, because I have an 02 and I have the 45rfe... And I know we have completely different mounts than the CRD. I always try to use the power of google before I ask a q? Unless I'm in a pinch for time! While I'm here I might as well ask another q? LoL... My new mounts have some open aired gaps in the rubber of the center of the mounts... Is that normal? They look brand new besides... Just trying to make sure I didn't get blems or something...


Yes, the gaps in the motor mounts are there by design. When they tear in any of the segments is when they need replaced. Like this:

Image

The torque specs from the factory service manual:

Engine Mount Bracket to Block Bolts 45 ft/lbs
Rear Mount to TransmissionBolts 34 ft/lbs

The through bolt procedure from the FSM:

Torque the through bolt retaining nut to 61 N·m (45 ft. lbs.).

Hope this is what you were looking for.

Bob
Page 1 of 1 All times are UTC - 5 hours [ DST ]
Powered by phpBB © 2000, 2002, 2005, 2007 phpBB Group
http://www.phpbb.com/