Pics show rubbing.. wtf is going on? This was supposed to fix my issues from before...
http://www.cardomain.com/usernew/galleries/edit.aspx?id=1152729
| LOST JEEPS http://www.lostjeeps.com/forum/phpBB3/ |
|
| alignment and vibration after jba a arms installed http://www.lostjeeps.com/forum/phpBB3/viewtopic.php?f=3&t=76815 |
Page 1 of 1 |
| Author: | riptricket [ Sat Sep 21, 2013 3:00 pm ] |
| Post subject: | alignment and vibration after jba a arms installed |
So I installed my upper a arms on both sides and had an alignment. I still have knocking and vibrations at 40+ mph. Do not know what to do at this point. Thank y'all |
|
| Author: | tommudd [ Sat Sep 21, 2013 4:02 pm ] |
| Post subject: | Re: alignment and vibration after jba a arms installed |
Tires, check balance and also for any issues with the tires themselves Have you checked for any loose parts/ improperly torqued parts? Have you check the CVs/ front driveshaft rear boot? Have you checked the rear u-joints ? I assume you had an issue before ? |
|
| Author: | riptricket [ Mon Sep 23, 2013 9:08 am ] |
| Post subject: | Re: alignment and vibration after jba a arms installed |
just got her aligned and maxed out on the left front side now while braking at 15 miles an hour horrible grinding noise occurs |
|
| Author: | riptricket [ Mon Sep 23, 2013 7:08 pm ] |
| Post subject: | Re: alignment and vibration after jba a arms installed |
the front right side is making thumping and rattling noises at approximately 45 miles an hour plus extremely hard at 55 |
|
| Author: | riptricket [ Mon Sep 23, 2013 7:45 pm ] |
| Post subject: | Re: alignment and vibration after jba a arms installed |
Pics show rubbing.. wtf is going on? This was supposed to fix my issues from before... http://www.cardomain.com/usernew/galleries/edit.aspx?id=1152729 |
|
| Author: | riptricket [ Tue Sep 24, 2013 3:02 pm ] |
| Post subject: | Re: alignment and vibration after jba a arms installed |
Just went to precision tune auto and he showed me where the springs and upper arms are rubbing... how does one fix this. I thought the upper a arms were supposed to fix all the issues with Frankenlift. |
|
| Author: | TheJawsOfDeath [ Wed Oct 02, 2013 8:00 am ] |
| Post subject: | Re: alignment and vibration after jba a arms installed |
Can you post the pics here? Your car domain link didn't work for me. I run OME 927s and 3 ring clevis in front, and I had to rotate the spring on one side to get the arm to fall between the coils at full droop. As far as the shaking and vibration just driving down the road, that sounds like a separate issue. |
|
| Author: | tommudd [ Wed Oct 02, 2013 8:12 am ] |
| Post subject: | Re: alignment and vibration after jba a arms installed |
riptricket wrote: Pics show rubbing.. wtf is going on? This was supposed to fix my issues from before... http://www.cardomain.com/usernew/galleries/edit.aspx?id=1152729 won't take us to your section so not sure plus how high are you sitting now ? If 23 or over then yes you're going to have spring/UCA hitting each other . Have to keep everything 22.5 and lower for no contact as far as your noises and grinding you're just going to have to track it down looking at CVs , front driveshaft boot, brakes etc |
|
| Page 1 of 1 | All times are UTC - 5 hours [ DST ] |
| Powered by phpBB © 2000, 2002, 2005, 2007 phpBB Group http://www.phpbb.com/ |
|