LOST JEEPS
http://www.lostjeeps.com/forum/phpBB3/

Which PML Aluminum Transmission Pan(s) w/SKIDROW Skidplate?
http://www.lostjeeps.com/forum/phpBB3/viewtopic.php?f=3&t=93175		 Page 1 of 1
Author:  JeepStar [ Sun Jul 12, 2026 3:19 pm ]
Post subject:  Which PML Aluminum Transmission Pan(s) w/SKIDROW Skidplate?
Hi Everyone,
Has anyone installed a PML Aluminum Transmission Pan with the SKIDROW Steel Transmission Skidplate???
I have a early 2002 Jeep Liberty KJ with a MOPAR replacement 3.7L V6 and factory 45RFE Auto Transmission.
I would like to order one of the several PML Aluminum Transmission Pans with a larger than stock fluid capacity, but I do not want the new pan to contact a SKIDROW Steel Transmission Skidplate. Has anyone had experience with this combination of aftermarket parts???
Any help would be appreciated. Thank you!
Author:  WWDiesel [ Mon Jul 13, 2026 1:16 am ]
Post subject:  Re: Which PML Aluminum Transmission Pan(s) w/SKIDROW Skidpla
I don't have the Skidrow skidplate, I made my own skidplate out of 3/16" flat plate steel. It is quite large, covers the transmission & transfer case.
When I upgraded my transmission pan to the PML deep sump oil pan, I had to add 2" spacers at the rear to clear the bottom of the oil pan.
You probably can do the same. The front attachment point was ok and cleared the oil pan, it is just the rear that had to be lowered.
I highly recommend the LubeLocker Oil Gasket to go with the PML aluminum deep sump oil pan.

NOTE: Both the gasket and PML oil pan fits the 45RFE transmission.

Quote:
PML 545RFE Transmission Deep Sump Oil Pan PN: 10304 (2 1/2 to 3 1/8 quarts over stock pan)
Fits Chrysler Dodge Jeep 68RFE, 66RFE, 65RFE, 545RFE, 45RFE Transmissions
LubeLocker Transmission pan Gasket LUB-LLT-CRFE

Shop around to find the best prices.
Summit Racing had one of the better prices on the LubeLocker gasket. https://www.summitracing.com/parts/lub-llt-crfe

See pictures:

Image

Image

Image
Author:  JeepStar [ Thu Jul 16, 2026 1:12 am ]
Post subject:  Re: Which PML Aluminum Transmission Pan(s) w/SKIDROW Skidpla
Thank you WWDiesel!
After reading your comments and viewing your photos, I ordered my PML transmission pan.
My 2002 KJ has a factory exhaust that crosses over the front of the pan requiring a relief cutout in the design of both the stock and PML pans. As a result, my PML options were reduced down to just 2 pans. Either the PML stock size replacement or 2 quarts over stock which is what I ordered. It is PML part number: 11079.
Unfortunately, the shipping time stated on the PML website is best-case-scenario-only and subject-to-change. In my case, the machining required for a temp sensor is going to cause a significant delay as PML currently have a backlog of orders. On a more positive note: Lori who answers their phones is awesome and very helpful. You may want to give Lori a call before placing a online order and if you are ordering from outside the USA, you will have to call Lori to place a phone order.
Page 1 of 1 All times are UTC - 5 hours [ DST ]
Powered by phpBB © 2000, 2002, 2005, 2007 phpBB Group
http://www.phpbb.com/