Hey guys,
Decided after a couple hard stops driving in Tucson last month at FITS that I should probably hook up a brake control system to help stop the trailer a bit easier. The PO installed electric brakes on in so i'm doing good there and with the 7 pin harness.

Any of you trailer haulers have any recommendations on what to use? I really like the Prodigy, but dont think I'll be able to source it locally in time for Mojave. What about the ones they sell at Autozone/ Checkers etc? They are considerably cheaper priced. Also thought i read that the controller has to be mounted horizontal, any truth in that or can it be mounted vertically?

Thanks
Mike

no AJ dont think i'll need jake brakes like your trailers. haha

Auto safety house on benson highway in tucson is where I had mine installed. Give them a call

_________________
2011 Nissan XTerra

Prodogy is a good option.
I use a Journey HD in my truck for stopping that 4800# max trailer you haveseen me with.
Furtunately even on single axles the electric braking system basically is all the same.

Didn't even know that AT had electric brakes- that is an extremely good option!

Roland

_________________
2006 CRD LTD 2.8L VM Motori turbo,CAC, 100K-new timing belt
ORM-SEGR, Trans cooler, CLIII hitch front/rear, Journey HD controller
Mopar skids,"Stone Soup" rails, KK clevis fork 1" mild lift w/Daystar stops
215x85 LRD BFG Commercial A/T's, Rola Rack, V6 airbox, Fumoto valve
10K winch, B5 Biodiesel (ULSD CP3 lube)
Its a Diesel baby!

ok on the topic of brake controllers do we need any additional harnesses to hook up to the KJ? i was looking at the prodigy as well and the web site says I need an additional harness. I do have the factory tow pkg.

http://www.etrailer.com/tv-wiring-Install-2006-Jeep-Liberty.aspx

here they are showing the additional harness install. Do i have to purchase this?

here are the main links:

http://www.etrailer.com/bc-2006_Jeep_Liberty.htm

http://www.etrailer.com/p-ETBC7.htm

Do I need all this stuff?

_________________
2016 JKU RUBICON

other mods coming soon...

Hey Doc, long time no talkie.

From what I've read, no that additional package would not be needed if you already have the factory tow pkg. I ended up buying(autozone) a trailer brake wiring setup for the extra lengths of wires for the install, but if you have plenty of connectors and wires you'd be fine.

There are four wires on the brake controller. One positive and one negative routed to the battery. One taps into the blue wire under the driver's side kick panel (behind hood latch). The last one taps into the brake light wire (white w/ brown stripe in brake harness above brake) Found it easy to pull the kick panel, the drop panel above the brake/gas pedals, and drop the knee panel under steering wheel to get to everything. hope that helps.

mike

very cool. thank you and yes its been a while since we have spoke.. I hope things are well on your end...

Mike

_________________
2016 JKU RUBICON

other mods coming soon...

thanks, yeah things are going good. we missed ya at FITS this year.

mike

I don't suppose you could be a lil more specific with the blue wire all I see is a Big stupid harness next to the hood latch. I did see a white with brown stripe as you said just above the pedals its in a lil harness or bundle or four wires.

_________________
2016 JKU RUBICON

other mods coming soon...

ok i found it and it was labeled but mine is red so anyhoo, did you just tap in to the white and brown wire ?

_________________
2016 JKU RUBICON

other mods coming soon...

yeah i put a "add a line" to the white w/ brown stripe. It was a hurried job, i need to go back and redo it all when i finally get around to ordering my controller (was using buddies).

mike

so when you do redo it how are u gonna do it are u gonna splice it or just remove some of the plastic and solder it or what.. man I hate wiring

_________________
2016 JKU RUBICON

other mods coming soon...