mine is hanging in the garage. the big engine cover.
| LOST JEEPS http://www.lostjeeps.com/forum/phpBB3/ |
|
| ENGINE Cover - Do i need it? http://www.lostjeeps.com/forum/phpBB3/viewtopic.php?f=5&t=23129 |
Page 1 of 2 |
| Author: | euromade [ Sun Aug 05, 2007 10:26 pm ] |
| Post subject: | ENGINE Cover - Do i need it? |
I just cleaned the MAP sensor and discovered a second cover that is conprised of two section that "bind" in the middle. Each section is held by 3+ screws. Question: Do I need this cover? there are wires that go from the top of the motor thru this cover and then they are covered by the main cover (the that says JEEP 2.8 CRD) thanks... |
|
| Author: | Larry R. [ Sun Aug 05, 2007 10:41 pm ] |
| Post subject: | |
no its for noise reduction. |
|
| Author: | dieseledkj [ Sun Aug 05, 2007 11:09 pm ] |
| Post subject: | |
That cover is the first thing a ditched when I purchased my CRD. A fancy cover that contains engine heat and noise, not on my Jeep. Actually I purchased the CRD partly because I like the sound of it running. |
|
| Author: | nursecosmo [ Sun Aug 05, 2007 11:18 pm ] |
| Post subject: | |
Don't need it. Personally I can't even tell the difference on or off. |
|
| Author: | euromade [ Sun Aug 05, 2007 11:43 pm ] |
| Post subject: | cool |
yeah, I didn't know if it realy had any purpose at all...my TDI runs with no cover as well. MAP cleaning will be a lot easier as well. Thanks for your input. |
|
| Author: | Cowcatcher [ Sun Aug 05, 2007 11:47 pm ] |
| Post subject: | Re: cool |
euromade wrote: yeah, I didn't know if it realy had any purpose at all...my TDI runs with no cover as well. MAP cleaning will be a lot easier as well.
Thanks for your input. WAIT A MINUTE!!!!! I don't think everyone carfully read your email. You can ditch the plastic CRD cover but that other think is a wire tray that keeps the wire harness off the hot parts of your motor. I would not discard that. |
|
| Author: | euromade [ Sun Aug 05, 2007 11:51 pm ] |
| Post subject: | ... |
OK, the wire tray is the one I'd like to live without, or maybe not. |
|
| Author: | skywarn [ Mon Aug 06, 2007 2:08 am ] |
| Post subject: | speaking of... |
i think im the only CRD with out a wire tray.... mine is nothing but wires wraped in ele. tape. and nothing more... would some one please step up so i dont feel so alone and incompleate with out my wire tray... BTW, my top cover stays on, but my sub covers are off. |
|
| Author: | TDI4BY [ Mon Aug 06, 2007 2:47 am ] |
| Post subject: | |
mine is hanging in the garage. the big engine cover.
|
|
| Author: | Cowcatcher [ Mon Aug 06, 2007 9:27 am ] |
| Post subject: | Re: speaking of... |
skywarn wrote: i think im the only CRD with out a wire tray.... mine is nothing but wires wraped in ele. tape. and nothing more... would some one please step up so i dont feel so alone and incompleate with out my wire tray...
BTW, my top cover stays on, but my sub covers are off. Did you purposely take the wire tray off or did you never have one? I guess I am more risk adverse than others. I don't find the tray a problem and there seems to be enough stuff on the CRD that can go south on you without adding to the problem by stripping parts off without some consideration as to why they were there in the first place. |
|
| Author: | euromade [ Mon Aug 06, 2007 10:29 am ] |
| Post subject: | |
I guess this "sub-tray" is designed to keep all the wires away from the top of the engine. I does make harder to get to the MAP sensor and such, but again, I will leave it there. The top tray, I think, is just for the show - maybe some sound reflection, but that is about it... |
|
| Author: | nix [ Mon Aug 06, 2007 10:38 am ] |
| Post subject: | |
euromade wrote: I guess this "sub-tray" is designed to keep all the wires away from the top of the engine. I does make harder to get to the MAP sensor and such, but again, I will leave it there. The top tray, I think, is just for the show - maybe some sound reflection, but that is about it...
Yep.. I wouldn't remove the "sub-tray". Somebody went through a lot of trouble to suspend those wires/hoses above the motor.. must be a reason. Mine was semi-unbolted when I cleaned my MAP sensor.. so I could easily just 'shimmy' up the sub-tray over the posts that it sits on. That made it easier for me to access the one bolt needed to loosen the MAP sensor. The large plastic "2.8 CRD" cover is simply for noise reduction. It also traps heat under it.. which may or may not be a good thing. I took mine off this last week and it seems to sound louder and my ProVent lines seem to be less hot now that they are not under the cover. |
|
| Author: | tulsa [ Mon Aug 06, 2007 11:47 am ] |
| Post subject: | |
I just cleaned the sensor, but it would be interesting to see if the tray could be modified to allow sensor removal W/O tray removal. Lewis |
|
| Author: | bugnout [ Mon Aug 06, 2007 11:50 am ] |
| Post subject: | |
I've never had to completely remove the cable tray, just pop it off the stud in back to get at the MAP sensor |
|
| Author: | Cowcatcher [ Mon Aug 06, 2007 12:09 pm ] |
| Post subject: | |
I was able to clean mine without removing the tray. |
|
| Author: | Joe Romas [ Mon Aug 06, 2007 12:14 pm ] |
| Post subject: | |
I hope you all have replaced the spring clip things with nuts
|
|
| Author: | nix [ Mon Aug 06, 2007 1:28 pm ] |
| Post subject: | |
Joe Romas wrote: I hope you all have replaced the spring clip things with nuts
Mine never had the nuts.. just the spring clips! |
|
| Author: | Stan Wright [ Mon Aug 06, 2007 2:51 pm ] |
| Post subject: | |
The service writer at the Bloomington, Indiana Jeep dealer made me bring my engine cover in before he'd release the Jeep to me. He said it was a "vital part of the motor". What a dork. 
http://eurekaboy.com/jeepcomplaintletter.htm |
|
| Author: | DZL_LOU [ Mon Aug 06, 2007 3:21 pm ] |
| Post subject: | |
Stan Wright wrote: The service writer at the Bloomington, Indiana Jeep dealer made me bring my engine cover in before he'd release the Jeep to me. He said it was a "vital part of the motor". What a dork.
Stan I remember you had to drive home to get the cover because you got lectured that it was vital to the motor functioning. I have told your story over again to my techs and we want to get an autograph of this dork! |
|
| Author: | Stan Wright [ Mon Aug 06, 2007 4:28 pm ] |
| Post subject: | |
You'll find him at the Bloomington, Indiana Jeep dealership sitting at the right hand of God...at least in his mind... 
|
|
| Page 1 of 2 | All times are UTC - 5 hours [ DST ] |
| Powered by phpBB © 2000, 2002, 2005, 2007 phpBB Group http://www.phpbb.com/ |
|