ASFIR Aluminum Skid...also protects the transfercase (chuck@asfir.com)
Or look to ALLJs at www.boulderbars.com but I think they quit making the transmission skid...and check out the For Sale Section at this forum for a used one at a good price
| LOST JEEPS http://www.lostjeeps.com/forum/phpBB3/ |
|
| Mopar Tranny Skid http://www.lostjeeps.com/forum/phpBB3/viewtopic.php?f=5&t=34646 |
Page 1 of 1 |
| Author: | COKJ06 [ Fri Aug 01, 2008 3:18 pm ] |
| Post subject: | Mopar Tranny Skid |
Does the Mopar tranny skid project the vulnerable oil filter? How tough is it? Has anyone landed on it in the rocks? Also, I know with the engine skid there was a thicker and thinner gauge metal version. Is it like that with the tranny skid? |
|
| Author: | BVCRD [ Fri Aug 01, 2008 3:45 pm ] |
| Post subject: | |
It's pretty thin and useless if you are in rocks at all. I have seen some that were mashed up to and around the tranny pan. The oil filter sits off to the side of the skid and is not protected by it. The filter sits up kind of high by itself and I have never come close to impacting it. |
|
| Author: | dgeist [ Fri Aug 01, 2008 4:05 pm ] |
| Post subject: | the one nice thing.... |
What is positive about them is that they're inexpensive and easy to obtain. If you know you're going to be beating on it, then it's probably not for you, but if you want occasional protection and piece of mind for barreling down fire roads and an occasional rock or tree branch, it may be all you need. |
|
| Author: | DarbyWalters [ Fri Aug 01, 2008 4:43 pm ] |
| Post subject: | |
ASFIR Aluminum Skid...also protects the transfercase (chuck@asfir.com)
Or look to ALLJs at www.boulderbars.com but I think they quit making the transmission skid...and check out the For Sale Section at this forum for a used one at a good price |
|
| Author: | ATXKJ [ Fri Aug 01, 2008 4:59 pm ] |
| Post subject: | |
I've bent mine up to where it's almost touching the tranny pan - and the oil filter is still safe (need to get a Skid Row - but I'm delaying to see if Rock Lizard comes up with something) |
|
| Author: | COKJ06 [ Fri Aug 01, 2008 5:17 pm ] |
| Post subject: | |
Thanks for the responses! I'm not looking to beat the skids, just want protection for that 'oops' scenario. The thing I don’t like about the skid row skid is it seems to use up too much ground clearance. I really like the fit the ASFIR skid, but not too crazy about aluminum, mainly because of the cost. I wish someone would duplicate the ASFIR design in 3/8 steel! Maybe I'll contact ASFIR and see if they would consider steel. |
|
| Author: | DarbyWalters [ Fri Aug 01, 2008 6:08 pm ] |
| Post subject: | |
Well remember that the Tranny skid also encompasses the Transfercase...so you get two for one price. The Tranny section is "vented" to let the tranny cool...they are 6mm thick...won't rust...and are light for better fuel economy. |
|
| Author: | BVCRD [ Fri Aug 01, 2008 6:31 pm ] |
| Post subject: | |
DW, I have heard that aluminum skids sort of drag over rocks instead of sliding like steel does. Sort of the way an aluminum canoe hangs up on riffles unlike ABS (plastic) canoes. Any thoughts? |
|
| Author: | 06 KJ Sport [ Mon Aug 04, 2008 4:09 pm ] |
| Post subject: | |
Anybody got a pic of the Mopar Tranny & Transfer Case Skids?? I went to install the set that I picked up and wouldn't you know it they would go on  . Apparently there should be some pre set nuts some where?? What I found is that I dont have any where to connect the plates to the jeep, unless I get out the drill 
|
|
| Author: | BlackLibertyCRD [ Mon Aug 04, 2008 8:46 pm ] |
| Post subject: | |
06 KJ Sport wrote: Anybody got a pic of the Mopar Tranny & Transfer Case Skids?? I went to install the set that I picked up and wouldn't you know it they would go on
. Apparently there should be some pre set nuts some where?? What I found is that I dont have any where to connect the plates to the jeep, unless I get out the drill The skids are supposed to come with nutzerts and install tool with instruction. The skids I got from the dealer did. |
|
| Author: | BVCRD [ Tue Aug 05, 2008 9:38 am ] |
| Post subject: | |
Mine did too. They go in the hole, and sort of expand, then that is the threaded nut you use on I think 2 of the bolts. |
|
| Author: | DarbyWalters [ Wed Aug 06, 2008 10:26 am ] |
| Post subject: | |
There is one FOR SALE in the Members For Sale Section |
|
| Page 1 of 1 | All times are UTC - 5 hours [ DST ] |
| Powered by phpBB © 2000, 2002, 2005, 2007 phpBB Group http://www.phpbb.com/ |
|