| LOST JEEPS http://www.lostjeeps.com/forum/phpBB3/ |
|
| Fumoto Valve http://www.lostjeeps.com/forum/phpBB3/viewtopic.php?f=5&t=46147 |
Page 1 of 1 |
| Author: | mikey1273 [ Wed Aug 26, 2009 4:22 pm ] |
| Post subject: | Fumoto Valve |
I want to order a Fumoto valve and new bleeder valve kit. if I get the one with the nipple so a can be put the hose on it will that reduce ground clearance by much? |
|
| Author: | linewarbr [ Wed Aug 26, 2009 4:27 pm ] |
| Post subject: | |
It will only further reduce clearance by the length of the nipple beyond the normal valve. I have the normal valve on mine, and it does not extend below the Mopar skid plate. I don't even have to jack mine up, I just reach under, turn the valve, crack the seal on the filter, and go chill for a minute while it drains. Is there a specific reason you want the one with the nipple? The regular valve gives you a controlled enough flow to easily fill an oil analysis container. |
|
| Author: | mikey1273 [ Wed Aug 26, 2009 4:33 pm ] |
| Post subject: | |
not really, I like the idea that the flow could be directed into any oil can. but not sure I want something longer hanging down from the bottom of my Jeep. I would still have to use a drain pan for the filter so I guess its not worth it. I'm going to order the plain one. Is the safety clip a good idea? |
|
| Author: | 95BadBoy [ Wed Aug 26, 2009 5:24 pm ] |
| Post subject: | |
Just recently added a F102 (no nipple). Drains nicely into the catch pan. I had thought about the longer version, ultimately could not see the need for having the extra length under the rig. |
|
| Author: | RJM [ Wed Aug 26, 2009 5:24 pm ] |
| Post subject: | |
The clip is a good idea, like wearing a belt and suspenders, your pants are sure not to fall down. I ordered the one with the nipple and ended up cutting it off with a hacksaw. |
|
| Author: | UFO [ Wed Aug 26, 2009 5:41 pm ] |
| Post subject: | |
mikey1273 wrote: Is the safety clip a good idea? It's good insurance.
|
|
| Author: | chadhargis [ Wed Aug 26, 2009 5:52 pm ] |
| Post subject: | |
Fumoto valves have a locking detent on them making it nearly impossible to open them by accident. I ordered the safety clip once, and never used it. I guess if you were wheeling, then it would be a good idea. |
|
| Author: | NJCRD [ Wed Aug 26, 2009 5:57 pm ] |
| Post subject: | |
I just put the f102n(nipple) on. I have skid row skid plates and it does not hang past the opening in the plate. I hated making a mess all over the skid plate. I went with the nipple so I can just run hose down into the pan and be done with it. You will have some trouble finding it as no one had the 102n. I'll pm you the guys info that I got mine from if you're interested. |
|
| Author: | mikey1273 [ Wed Aug 26, 2009 6:27 pm ] |
| Post subject: | |
well I ordered the valve with no nipple and a safety ring. |
|
| Author: | mikey1273 [ Wed Aug 26, 2009 6:35 pm ] |
| Post subject: | |
I ordered mine here http://lubricationspecialist.com/front/ ... parentid=0 someone here gave me the link when I was first looking into getting a CRD. they list a CAT 2 micron fuel filter on that page too.... I wanted that as well but was not sure if it was a perfect fit so I called and asked. good I thing I did b/c it went with a conversion kit they don't sell for our CRD anymore. I can get a fuel filter at NAPA for like $32 minus 7% AAA member discount. I am going to put all this on before it gets cold so I don't have any routine stuff to do during the coldest months |
|
| Author: | Cowpie1 [ Wed Aug 26, 2009 9:06 pm ] |
| Post subject: | |
I got the Fumoto for my Jeep early on and also put one on my semi. really good move. I also, haven't used the clip and never had a problem. I run the Jeep around my farm a lot, and I have dented the nipple on the valve. Not much of a dent but I used a small punch, I spread it out again. Soft brass is easy to reform. Have the nipple on the valve on my semi as well. Never any problem. I like the nipple feature only because it gives a little more gap between the lever and the flowing oil. |
|
| Author: | KJ 119 [ Wed Aug 26, 2009 10:10 pm ] |
| Post subject: | |
RJM wrote: I ordered the one with the nipple and ended up cutting it off with a hacksaw.
Ditto |
|
| Page 1 of 1 | All times are UTC - 5 hours [ DST ] |
| Powered by phpBB © 2000, 2002, 2005, 2007 phpBB Group http://www.phpbb.com/ |
|