LOST JEEPS
http://www.lostjeeps.com/forum/phpBB3/

Favorite code reader/scan tool?
http://www.lostjeeps.com/forum/phpBB3/viewtopic.php?f=5&t=56949		 Page 1 of 1
Author:  Biosmell [ Wed Nov 17, 2010 1:58 pm ]
Post subject:  Favorite code reader/scan tool?
Hi Guys,

What are people's favorite scan tool for reading and clearing codes that is inexpensive and also works on the CRD?

I am going to need one sooner or later for both the CRD and the Dodge 2500.

Also I have been searching this forum, is there a place listing codes. I have the factory manual, but it says to refer to the "factory code manual".

Thanks!

El Jefe
Author:  reka12 [ Wed Nov 17, 2010 2:26 pm ]
Post subject:  Re: Favorite code reader/scan tool?
My GDE Ecotune Flash tool! :D
Author:  Biosmell [ Wed Nov 17, 2010 2:43 pm ]
Post subject:  Re: Favorite code reader/scan tool?
You know I do have the Eco-tune, but I haven't yet picked up their flash tool.

El Jefe
Author:  jinstall [ Wed Nov 17, 2010 11:00 pm ]
Post subject:  Re: Favorite code reader/scan tool?
Ross-Tech VAGCOM but it works on VW's as well for other control features.
Author:  Joe Romas [ Thu Nov 18, 2010 7:47 am ]
Post subject:  Re: Favorite code reader/scan tool?
jinstall wrote:
Ross-Tech VAGCOM but it works on VW's as well for other control features.


My Vag-com that has CAN using it's OBDii mode" has worked with every 96 and newer vehicle I've tried it on. Most recently on my 2000 Cherokee "classic". It had a random misfire on cylinder 3. A common problem with heat causing the injector to overheat. I cured that by fashioning a small aluminum heat shield.

It will give you readings for things like coolant temperature, throttle position, rpm's, ambient air temperature, intake air temperature and more.

But for what it will do on our CRD's it's a expensive solution unless you have a VW too then it's a "must have" :jester:

Too bad there's not a "VAG-COM" type solution for Chrysler specific items like VC does for VW's :(
Author:  tjkj2002 [ Thu Nov 18, 2010 11:14 am ]
Post subject:  Re: Favorite code reader/scan tool?
Sure a bit out of most's price range but the best out there,getting one after I pay my box off.

http://www1.snapon.com/diagnostics/us/verus
Author:  LibertyCRD [ Thu Nov 18, 2010 1:12 pm ]
Post subject:  Re: Favorite code reader/scan tool?
What about that new Ultra Guage? I hear it's awesome and does a ton of stuff for $40. Will it work with the CRD?
Author:  DynoPax [ Thu Nov 18, 2010 5:01 pm ]
Post subject:  Re: Favorite code reader/scan tool?
LibertyCRD wrote:
What about that new Ultra Guage? I hear it's awesome and does a ton of stuff for $40. Will it work with the CRD?


I posted a request on Ultragauge's forum, and got replied quite fast, actually! Basically, they said it was impossible to test every possible combinations out there (understandable!), but a few Liberty owners confirmed the product's viability with their vehicle (except this is with the 3.7L), which makes it irrelevant for CRD owners.

Reading the online owner manual, I could see they have particular adjustable settings, as far as the Chrysler 9141 protocol is concerned. It basically prevents constant protocol readout, though I doubt this would suffice to avoid issues (there is a constant heartbeat pinging going on)...

Still, it looks interesting for the price... Heck, I may even be willing to serve as a guinea pig and buy one! Worst case, if unable to use it in operating mode, it still can be useful to read code and reset them.
Author:  MOSFET [ Thu Nov 18, 2010 7:43 pm ]
Post subject:  Re: Favorite code reader/scan tool?
I have this http://www.amazon.com/Actron-CP9125-PocketScan-Code-Reader/dp/B0007LEG2K, and it has worked quite well for reading codes and turning off the MIL. ~$60
Author:  10000degrees [ Sat Nov 20, 2010 1:58 am ]
Post subject:  Re: Favorite code reader/scan tool?
iPhone specifically, probably other smart phones too, google search iPhone obdII reader. I am gonna buy one of the non-wifi or bt interfaces. I like the cable and it charges the phone too IPhone obd software looks to be pretty amazing and comparatively, CHEAP!
Author:  flman [ Sat Nov 20, 2010 9:30 am ]
Post subject:  Re: Favorite code reader/scan tool?
tjkj2002 wrote:
Sure a bit out of most's price range but the best out there,getting one after I pay my box off.

http://www1.snapon.com/diagnostics/us/verus


But will it work on a Sprinter NCV3?
Author:  AJN [ Sat Nov 20, 2010 4:58 pm ]
Post subject:  Re: Favorite code reader/scan tool?
10000degrees wrote:
iPhone specifically, probably other smart phones too, google search iPhone obdII reader. I am gonna buy one of the non-wifi or bt interfaces. I like the cable and it charges the phone too IPhone obd software looks to be pretty amazing and comparatively, CHEAP!


Eh... I went hog wild on that idea and wish I'd spent the time and resources elsewhere. When it works it's nice, but frequently it fails to load and/or freezes. I'm hoping updates will cure some of the issues.

I would go a different direction if you want serious data acquisition and control via either dedicated ODBII boxes, or one of the better PC based solutions like AutoEngenuity with their additional Enhanced Chrysler Expansion pack.
Author:  LibertyCRD [ Sat Nov 20, 2010 7:03 pm ]
Post subject:  Re: Favorite code reader/scan tool?
Will the digital scanguage/ ultraguage units show things like boost pressure and EGT temperature on our Jeeps? Something electronic would be much simpler to install. Plus you could see trouble codes.

And.. looking at the Scan Guage I noticed this note: "Jeep Liberty with the diesel engine does not report fuel use or trip functions and some of the gauges. Unless the recall ECU software update has been completed." What does it mean by "recall ECU software update"?
Author:  tjkj2002 [ Sat Nov 20, 2010 8:54 pm ]
Post subject:  Re: Favorite code reader/scan tool?
flman wrote:
tjkj2002 wrote:
Sure a bit out of most's price range but the best out there,getting one after I pay my box off.

http://www1.snapon.com/diagnostics/us/verus


But will it work on a Sprinter NCV3?

Yes if you add the correct software just like any other scanner.
Author:  yakers [ Sun Nov 21, 2010 1:15 am ]
Post subject:  Re: Favorite code reader/scan tool?
10000degrees wrote:
iPhone specifically, probably other smart phones too, google search iPhone obdII reader. I am gonna buy one of the non-wifi or bt interfaces. I like the cable and it charges the phone too IPhone obd software looks to be pretty amazing and comparatively, CHEAP!


Anybody using an OBD II scanner on their iphone/pod or other smartphone on their CRD or any vehicle? Seems like a good idea to me if it works.
Author:  AJN [ Sun Nov 21, 2010 2:12 am ]
Post subject:  Re: Favorite code reader/scan tool?
yakers wrote:
10000degrees wrote:
iPhone specifically, probably other smart phones too, google search iPhone obdII reader. I am gonna buy one of the non-wifi or bt interfaces. I like the cable and it charges the phone too IPhone obd software looks to be pretty amazing and comparatively, CHEAP!


Anybody using an OBD II scanner on their iphone/pod or other smartphone on their CRD or any vehicle? Seems like a good idea to me if it works.


Yea, I already commented with my experience. I have GoLink hardware and DashCommand software, which is one of the more thorough ODB applications, but it's frustrating using it due to frequent freezes and errors where it can't communicate with, or find the interface.
Author:  10000degrees [ Thu May 19, 2011 9:49 pm ]
Post subject:  Re: Favorite code reader/scan tool?
AJN wrote:
yakers wrote:
10000degrees wrote:
iPhone specifically, probably other smart phones too, google search iPhone obdII reader. I am gonna buy one of the non-wifi or bt interfaces. I like the cable and it charges the phone too IPhone obd software looks to be pretty amazing and comparatively, CHEAP!


Anybody using an OBD II scanner on their iphone/pod or other smartphone on their CRD or any vehicle? Seems like a good idea to me if it works.


Yea, I already commented with my experience. I have GoLink hardware and DashCommand software, which is one of the more thorough ODB applications, but it's frustrating using it due to frequent freezes and errors where it can't communicate with, or find the interface.


FYI, I have used the tool on quite a few vehicles, BMW-Toyota and so far all the other ones were fine and communicated correctly. I remember reading on here that many, if not most generic scanners have connectivity issues. I can't quote the thread exactly, but something to the effect of mopar's software working like a virus to hack into the VM software control. Troll around on here enough and you'll find the thread.
Author:  tulsa [ Mon May 23, 2011 10:09 am ]
Post subject:  Re: Favorite code reader/scan tool?
LibertyCRD wrote:
Will the digital scanguage/ ultraguage units show things like boost pressure and EGT temperature on our Jeeps? Something electronic would be much simpler to install. Plus you could see trouble codes.

And.. looking at the Scan Guage I noticed this note: "Jeep Liberty with the diesel engine does not report fuel use or trip functions and some of the gauges. Unless the recall ECU software update has been completed." What does it mean by "recall ECU software update"?


I believe it was known as F31, done because the CRD worked with almost no OBDII tools except Chryslers. I believe the Feds pushed Chrysler to make the CRD more compliant.
Lewis
Page 1 of 1 All times are UTC - 5 hours [ DST ]
Powered by phpBB © 2000, 2002, 2005, 2007 phpBB Group
http://www.phpbb.com/