LOST JEEPS
http://www.lostjeeps.com/forum/phpBB3/

05 Liberty Half shaft Issue
http://www.lostjeeps.com/forum/phpBB3/viewtopic.php?f=5&t=72481		 Page 1 of 1
Author:  65Corvair [ Mon Nov 12, 2012 10:51 pm ]
Post subject:  05 Liberty Half shaft Issue
It appears that there is some rubbing between the inside joint of the passenger half shaft and the frame that holds the diff. I noticed this issue when I was installing the skid plate and changing the gear oil in the front differential. Recently when putting in Full time and part time, I have head some humming or gear noise at highway speeds, but only under acceleration. I would assume that this is the problem.For a bonus, I have included a poor quality video to show how the inner joint can move about.

Later this week I plan to take it apart an take a look in there. Any suggestions on what I should check?

Video:
http://youtu.be/NDkOskzzZ_I

Image
Author:  tjkj2002 [ Mon Nov 12, 2012 10:55 pm ]
Post subject:  Re: 05 Liberty Half shaft Issue
That would most likely be a worn intermediate shaft.Time for a new CV axle(remaned only,do not buy those labeled "new") and intermediate shaft.
Author:  Tree Catcher [ Mon Nov 12, 2012 11:59 pm ]
Post subject:  Re: 05 Liberty Half shaft Issue
I have the same humming sound but its when I am over about 40 mph. I also notice that when I turn to the left the hum goes away. Do you have the same problem?
Author:  65Corvair [ Tue Nov 13, 2012 2:42 pm ]
Post subject:  Re: 05 Liberty Half shaft Issue
For me it is much more noticeable above 40 and especially during acceleration, but only when I am in part-time or full-time. It does not seem to make a difference when I am turning though.

I have been reading about how to fix this, I think I will be able to do it, but the only "special" tool is a 34mm socket. Are there any other tools needed that are out of the ordinary?
Author:  tjkj2002 [ Tue Nov 13, 2012 2:46 pm ]
Post subject:  Re: 05 Liberty Half shaft Issue
The hub nut is 35mm,some came with 36mm hub nuts,not 34mm.
Author:  65Corvair [ Tue Nov 13, 2012 10:46 pm ]
Post subject:  Re: 05 Liberty Half shaft Issue
Going through the parts micro fiche it looks like i need to get:

Half Shaft, Right - 05066022AA
#2 Axle Shaft - 05066057AB
#3 Snap Ring, Axle Shaft - 05069009AA (Not Pictured)
#4 O Ring, Axle shaft - 05066067AA (Not Pictured)

Would I need need new seals or bearings?

Image
Author:  65Corvair [ Thu Nov 15, 2012 12:47 am ]
Post subject:  Re: 05 Liberty Half shaft Issue
Parts are ordered, I will update once I have this done or if I run into issues.
Author:  65Corvair [ Fri Nov 30, 2012 12:00 am ]
Post subject:  Re: 05 Liberty Half shaft Issue
I finally got all my parts in and was able to make the repair. It went very well following the factory service manual. The only issue I had was getting the lower control arm off of the lower ball joint. I tried a number of things, but what word was taping a wedge shaped object between the lower control arm and the front knuckle. (the red line)

Image

The intermediate shaft I ordered already had the clips on the shaft so I did need the ones I ordered separately. Anyone need them? :D

Where I bought the shaft:http://www.amazon.com/Omix-Ada-16523-43-Axle-Shaft/dp/B0034KU8OQ/ref=sr_1_1?ie=UTF8&qid=1327449580&sr=8-1

The half shaft I bought at Napa was good except the inboard boot had a lot of air in it. I removed the clip and removed a the excess air and the boot fit much better.
Author:  camo [ Fri Aug 16, 2013 11:09 pm ]
Post subject:  Re: 05 Liberty Half shaft Issue
Did replacing the axle shaft did it for you? what other parts you had to replace?
Author:  65Corvair [ Sat Aug 17, 2013 12:20 am ]
Post subject:  Re: 05 Liberty Half shaft Issue
I replaced the intermediate shaft (which included snap rings) and the passenger CV shaft. I replaced both parts at the same time and it worked great.
Author:  camo [ Sat Aug 17, 2013 12:33 am ]
Post subject:  Re: 05 Liberty Half shaft Issue
nice. how long did the job take? did you encounter any problems or needed any special tools?
Author:  riptricket [ Thu Oct 31, 2013 9:26 pm ]
Post subject:  Re: 05 Liberty Half shaft Issue
What is the torque spec for the hub nut
Page 1 of 1 All times are UTC - 5 hours [ DST ]
Powered by phpBB © 2000, 2002, 2005, 2007 phpBB Group
http://www.phpbb.com/