| LOST JEEPS http://www.lostjeeps.com/forum/phpBB3/ |
|
| Where can I find a list of torque specs for the Liberty? Lo http://www.lostjeeps.com/forum/phpBB3/viewtopic.php?f=5&t=79539 |
Page 1 of 1 |
| Author: | jrsavoie [ Sat Jul 05, 2014 12:43 pm ] |
| Post subject: | Where can I find a list of torque specs for the Liberty? Lo |
Where can I find a list of torque specs for the Liberty? Looking for torque specs for a 2006 Jeep Liberty CRD 2.8 liter diesel. transfer case cross member bolts, 3 on either end M10x1.5 power steering pump to bracket bolts - 3 little bolts. Power steering pump pulley - 3 little bolts Aluminum wheels lug nuts - 100 ft lbs. This I have not verified anywhere power steering pump / serpentine belt bracket tensioner to block bolts - 3 each. - 35 foot lbs Tensioner to power steering pump / serpentine belt bracket bolt. 43.6672 ft lbs or 47 Nm What is the correct name for the power steering pump / serpentine belt bracket? It is called either / or in different parts of the books part number Mopar 05093935AA Is there a place to find all these torque specs AND MORE? Somebody mentioned that there is a European manual online that is much easier and more detailed than than the 3 manual set. I haven't found it yet Thank you much. viewtopic.php?f=16&t=31005&p=837547#p837547 viewtopic.php?f=59&t=79393 Missing from the shroud removal instructions or I missed it is to take the bottom piece off the shroud for easier removal. I'm replacing the plastic button snaps with nutserts for easier removal |
|
| Author: | 3Dglasses [ Fri Jul 11, 2014 12:12 am ] |
| Post subject: | Re: Where can I find a list of torque specs for the Liberty? |
Here is what I was able to find: http://en.wikibooks.org/wiki/Jeep_Liber ... cket_Sizes |
|
| Author: | Mike92104 [ Fri Jul 11, 2014 12:50 am ] |
| Post subject: | Re: Where can I find a list of torque specs for the Liberty? |
http://colorado4wheel.com/manuals/Jeep/KJ/ |
|
| Author: | Hexus [ Fri Jul 11, 2014 7:51 am ] |
| Post subject: | Re: Where can I find a list of torque specs for the Liberty? |
Mike has the right link, the full Field Service Manual. The torque specs are in their respective sections. There's also a parts Fiche floating around on that site too if you need it. |
|
| Author: | dirtmover [ Fri Jul 11, 2014 8:55 am ] |
| Post subject: | Re: Where can I find a list of torque specs for the Liberty? |
FSM but most important of all use some common sense. There are known mistakes in the FSM that others have fallen victim to. If they spec 150 ft-lbs for an M10 screw it's probably wrong! |
|
| Author: | Auberon [ Fri Jul 18, 2014 10:46 am ] |
| Post subject: | Re: Where can I find a list of torque specs for the Liberty? |
Indeed there are some questions that have arisen but fortunately I grew up with the Imperial systems (all of them - BA and Holzhafels) and the tedious and expensive change to Metric. I seriously think there is a loss of translation from these initial tables to those later in the manual for the specific sections. Getting my hands on my paper version of the FSM made me realise this. Why would you think to put the definitive information on the very front of the manual for fastener selection and torque data? In this Introduction, of the FSM , there appear, however, to be no errors I've found YET (it's at least in the paper version) but if it looks odd I always look it up in the multiplicity of Engineering refs I have unless it is covered in this front Introduction section. These early Charts look accurate but some differences creep in later. I do think folk get worried about how much torque can be comfortably imparted onto a 1.0 mm Pitch set screw compared to a 1.25 P screw compared to a 1.5 mm P etc. with a given % thread engagement and of course it depends on lubed or not. As an aside: We chose to metricate - it's been a darned expensive thing having ALL the common British imperial taps, dies etc to hand for UNF, BSF, UNC, BSW, BSP, NPT, Holzhafel, B.A etc and then all the common metrics - in coarse, medium and fine. Sheesh. It's worse than tooling up for a new lathe. Thank goodness reamers cross over. FOR ACCURATE TORQUE SPECS: they can be found in: FSM INTRODUCTION: Page 2 has Fastener Identification - bolt marking and torques Metric as well as (on page 2 ) Bolt Markings and Torques - U.S. Customary. Page 3 has How to determine Bolt strength on page 2 of this Introduction. Page 8 has Torque References Some of the confusion seems to come from the typing of fasteners under the metric system and whether they're pre-lubed or not and basic typos. I hate the digital version except to carry on the road. The paper one in 4 volumes is much more comforting (tactile) and easy to browse around. Hope that helps. |
|
| Page 1 of 1 | All times are UTC - 5 hours [ DST ] |
| Powered by phpBB © 2000, 2002, 2005, 2007 phpBB Group http://www.phpbb.com/ |
|