Hi Team,

I was in Death Valley last weekend (amazing trip):





I had to use 4x4 a couple of times and I came down on something pretty hard. Looks like I dented my transmission pan. I haven't noticed any adverse effects so far. Does anyone think I should be worried?

I'm hooked: I'm looking at the Old Man Emu lift for my next adventure out there.

_________________
2006 CRD w/99,300 miles
F31 from a previous life
EHM @ 42K, ProVent @ 79K
GDE Eco Tune & TCM @ 46K
Engine mounts replaced @ 55k/93k, Timing Belt @ 90k
Lift Pump @ 97k
OME Lift, 1.5''
Kenwood TM-V71 Ham Radio / Cobra C75WX CB
Surf Racks

If it doesn't leak, don't worry about it, there is nothing as low inside the pan as where you dent it.

_________________
2005 kj CRD, samco, suncoast tc, provent, Kennedy lift pump, GDE ECO full torque, 2nd gen filter head, 245/70/16 a/t tires, mopar light bar, fumoto oil valve, OEM Skid Plates, ARB Front bumper and HD OME, tru cool LPD47391 40k GVW tranny cooler (stock cooler delete), FF Dynamics e-fan and shroud, rocker arms replaced, HDS2 190F thermostat.

Cool, thanks thermorex!

_________________
2006 CRD w/99,300 miles
F31 from a previous life
EHM @ 42K, ProVent @ 79K
GDE Eco Tune & TCM @ 46K
Engine mounts replaced @ 55k/93k, Timing Belt @ 90k
Lift Pump @ 97k
OME Lift, 1.5''
Kenwood TM-V71 Ham Radio / Cobra C75WX CB
Surf Racks

That wouldn't happen if you had skid plates......just saying. Its real cheap insurance

Sent from my SM-N900P using Tapatalk

_________________
I am the G.O.A.T.

True, true!

_________________
2006 CRD w/99,300 miles
F31 from a previous life
EHM @ 42K, ProVent @ 79K
GDE Eco Tune & TCM @ 46K
Engine mounts replaced @ 55k/93k, Timing Belt @ 90k
Lift Pump @ 97k
OME Lift, 1.5''
Kenwood TM-V71 Ham Radio / Cobra C75WX CB
Surf Racks

I had one 4" deep for over a year. If it doesn't leak, don't worry about it!

_________________
Silver 2006 KJ 2.8L CRD Limited:
GDE ECO Tune / Fumoto Valve / E-Tecno GX3123 7v Glow Plugs / 2nd Gen Fuel Head / Mishimoto RED Hoses / Rockers/Lifters @ 114k / Hayden FC + 11 Blade Nylon / Sears P1 Battery / Transgo 45RFE-HD2 Reprogramming Kit / Timken Front Bearings

Next time you have the pan off to service transmission, lay the pan flat on a large wooden board like a piece of 2x10 and take a large hammer and gently beat the dent out of the pan. Done this many times on other vehicles that had dents in the bottom of the pan...and it works like a champ!!!

_________________
Supporting Vendor and Moderator of LOST
05 Jeep Liberty CRD Limited
Ironman Springs/Bilstein/Shocks
Yeti StgIV Hot Tune
Week's BatteryTray
No FCV/EGR
Samcos/ProVent
SunCoast/Transgo
Carter Intank-pmp
2mic.Sec.Fuel Filter
Flowmaster/NO CAT
V6Airbox/noVH
GM11 Bld.fan/HDClutch
IronrockArms/wwdieselMount
98 Dodge Cummins 24 Valve

I'm gonna go outside and check to make sure you didn't steal my transmission oil pan cuz you pic looks identical to my oil pan.