| LOST JEEPS http://www.lostjeeps.com/forum/phpBB3/ |
|
| Mann provent install question http://www.lostjeeps.com/forum/phpBB3/viewtopic.php?f=5&t=85403 |
Page 1 of 1 |
| Author: | CRD-DAN [ Mon Oct 10, 2016 3:07 pm ] |
| Post subject: | Mann provent install question |
Looked at a couple installs of the provent. Every one I have seen so far doesn't route the collected oil back into the motor. Is it more trouble than its worth? Has anyone done this on the forum? |
|
| Author: | flash7210 [ Mon Oct 10, 2016 4:04 pm ] |
| Post subject: | Re: Mann provent install question |
Drilling a hole in the pan for draining the collected oil is definitely more trouble than it's worth. |
|
| Author: | CRD-DAN [ Mon Oct 10, 2016 6:31 pm ] |
| Post subject: | Re: Mann provent install question |
Couldn't agree with you more. I take it there is no factory hole to use ? |
|
| Author: | WWDiesel [ Mon Oct 10, 2016 8:51 pm ] |
| Post subject: | Re: Mann provent install question |
Simple solution; put a drain hose on the bottom of the ProVent long enough to route it down to an area near the frame rail and install a small manual drain valve on the end of the hose! Every so often, open the drain and drain the ProVent drain tube in a container and dispose of the liquid. I drain mine about once every other month and get about a shot glass (1oz.) or less out of it... 
|
|
| Author: | PZKW108 [ Tue Oct 11, 2016 12:00 am ] |
| Post subject: | Re: Mann provent install question |
when you will see how the oil from the provent drain looks like , you won't want to have it back in your engine !! |
|
| Author: | blk05liberty [ Tue Oct 11, 2016 10:42 am ] |
| Post subject: | Re: Mann provent install question |
Anyone know off the top of thier head what size hose to use? |
|
| Author: | WWDiesel [ Tue Oct 11, 2016 3:10 pm ] |
| Post subject: | Re: Mann provent install question |
blk05liberty wrote: Anyone know off the top of their head what size hose to use? For the ProVent 200: drain hose, use 1/2 oil rated hose! inlet & outlet, use a short piece of 1" hose, then a reducer fitting down to 3/4 hose to fit the stock CCV & air intake boot locations... Put clamps on all connections... See this web page for all specfications on the Mann Provent Filters:>https://www.mann-hummel.com/fileadmin/user_upload/service/catalogues/pdf/ProVent_en_2013.pdf 
|
|
| Author: | CRD-DAN [ Wed Oct 12, 2016 9:12 pm ] |
| Post subject: | Re: Mann provent install question |
Thanks for all the info. I looked on the Mann Hummel web page and it suggested a reroute back into the engine, that was the only reason I was asking. I have collected all of my parts and just started assembling. This thing sure doesn't go anywhere real easy. I was shooting for an install in a nook next to the power steering reservoir with one hose running under the coolant reservoir. Doesn't seem likely with these huge 1" pieces with reducers on them. Anyone have a photo with their provent installed on the passenger side ? |
|
| Author: | WWDiesel [ Thu Oct 13, 2016 9:34 am ] |
| Post subject: | Re: Mann provent install question |
CRD-DAN wrote: Anyone have a photo with their provent installed on the passenger side ? Made a bracket out of aluminum, bolted it to the back side of vacuum reservoir/solenoid assembly and then bolted the ProVent filter bracket to it... Routed the bottom outlet hose from the filter underneath the coolant reservoir and back to the turbo intake boot.  And yes, it is a tight fit and not a lot of room under the hood anywhere else to mount it since I have a 2 micron secondary fuel filter mounted on the other side of the engine....  Here is mine!  
|
|
| Author: | CRD-DAN [ Mon Oct 17, 2016 11:56 am ] |
| Post subject: | Re: Mann provent install question |
Thank you very much for taking the time to snap a photo of that. It's exactly where I want to install it. |
|
| Author: | HER_CRD [ Sat Oct 29, 2016 11:26 am ] |
| Post subject: | Re: Mann provent install question |
 Has anyone been able to install their provent with this connectors there or do they need to be moved? |
|
| Author: | WWDiesel [ Mon Oct 31, 2016 2:27 pm ] |
| Post subject: | Re: Mann provent install question |
I went and looked at mine, the ProVent is not long enough that the connectors get in the way, it kinda sets up slightly above them if mounted at the correct height... 
|
|
| Author: | HER_CRD [ Mon Oct 31, 2016 9:40 pm ] |
| Post subject: | Re: Mann provent install question |
Alright, thanks. Was looking at it on Saturday trying to figure out how to fit it in there. |
|
| Page 1 of 1 | All times are UTC - 5 hours [ DST ] |
| Powered by phpBB © 2000, 2002, 2005, 2007 phpBB Group http://www.phpbb.com/ |
|