Hey!

I'm getting ready to install a new turbocharger and removed the Turbo Charger Oil Feed Line (5142607AA) to replace it but there appears to be an adapter on the end that screws into the engine and it is well and truly stuck on the feed line.

Does anyone know the part number? I can't seem to find it on any diagrams.

Thanks, Nick

IDParts.com:> https://www.idparts.com/turbo-oil-feed- ... -5673.html
&
https://www.idparts.com/turbocharger-oi ... -3209.html

OEM Part Number: 5142792AA
Manufacturer Number: 5142792AA
Turbo Oil Feed Line Banjo Bolt for the Liberty CRD

_________________
Supporting Vendor and Moderator of LOST
05 Jeep Liberty CRD Limited
Ironman Springs/Bilstein/Shocks
Yeti StgIV Hot Tune
Week's BatteryTray
No FCV/EGR
Samcos/ProVent
SunCoast/Transgo
Carter Intank-pmp
2mic.Sec.Fuel Filter
Flowmaster/NO CAT
V6Airbox/noVH
GM11 Bld.fan/HDClutch
IronrockArms/wwdieselMount
98 Dodge Cummins 24 Valve

I think the op is talking about the rubber grommet on the return into the block.

_________________
Bill

Las Vegas, NV

2005 CRD Limited just purchased. 189,000 miles...
GDE Full Torque tune
Sasquatch: Provent, Stage 2 delete.
Bosch 5 volt steel Glow Plugs
GDE Full Torque tune
GDE TCM tune
Sasquatch Upgraded turbo

Former CRD.
2006 Libby CRD Sport
GDE Green tune
OME Springs all four corners, Rancho shocks and struts.
Revo 245/75/16's

The part number the OP listed, 5142607AA is for the OIL FEED LINE, NOT the rubber grommet.

But if you want the rubber grommet:
Turbocharger Oil Return Line Bottom Grommet (Liberty CRD) Part No. 5142794AA
https://www.idparts.com/turbocharger-oi ... dgda0br462

_________________
Supporting Vendor and Moderator of LOST
05 Jeep Liberty CRD Limited
Ironman Springs/Bilstein/Shocks
Yeti StgIV Hot Tune
Week's BatteryTray
No FCV/EGR
Samcos/ProVent
SunCoast/Transgo
Carter Intank-pmp
2mic.Sec.Fuel Filter
Flowmaster/NO CAT
V6Airbox/noVH
GM11 Bld.fan/HDClutch
IronrockArms/wwdieselMount
98 Dodge Cummins 24 Valve

JeepLovR,

The part number your looking for is 5066814AA. This is the fitting that screws into the block that the turbo oil feed line threads onto. I had the same issue on my engine rebuild! It was readily available from my Jeep dealer.

_________________
2005 KJ CRD Limited 4x4
ARP Head Studs
GDE Hot Tune / Trans Eco Tune
HDS Model 001 Thermostat (203°F)
Suncoast TC / Transgo Kit
Full EGR Kit
Bosch 5V Glow Plugs
NAPA HD Fan Clutch / GM 11-Blade Fan
Samco Silicon Charge Air Hoses
Carter In-tank Fuel Pump
Provent 200 with Sasquatch Install Kit
Sasquatch Silicon Turbo Inlet Hose
Bilstein Shocks

Many of the Mopar online dealers list that part number as being available for less than 10 bucks if you can't find it locally.

_________________
Supporting Vendor and Moderator of LOST
05 Jeep Liberty CRD Limited
Ironman Springs/Bilstein/Shocks
Yeti StgIV Hot Tune
Week's BatteryTray
No FCV/EGR
Samcos/ProVent
SunCoast/Transgo
Carter Intank-pmp
2mic.Sec.Fuel Filter
Flowmaster/NO CAT
V6Airbox/noVH
GM11 Bld.fan/HDClutch
IronrockArms/wwdieselMount
98 Dodge Cummins 24 Valve

Perfect! Yes RDBUL that's what I'm looking for!
Thanks for your help guys