LOST JEEPS
http://www.lostjeeps.com/forum/phpBB3/

Fun at work today.
http://www.lostjeeps.com/forum/phpBB3/viewtopic.php?f=6&t=29090		 Page 1 of 1
Author:  CD [ Thu Jan 31, 2008 5:34 am ]
Post subject:  Fun at work today.
:D

Image
Image
Image
Author:  ed. [ Thu Jan 31, 2008 5:42 am ]
Post subject: 
Get back to work :lol:
Author:  CD [ Thu Jan 31, 2008 6:02 am ]
Post subject: 
ed. wrote:
Get back to work :lol:


Come on Ed, don't be like that :lol:

Sway bar is still connected, I'm sure I have more to go if it was disco :twisted:
Author:  dloc_jeep_KJ [ Thu Jan 31, 2008 9:46 am ]
Post subject: 
yeah take it off!!! no pun intended. :lol: :oops: :P anyways yeah it will make a diff.
Author:  cmohr [ Thu Jan 31, 2008 9:06 pm ]
Post subject: 
Your a funny man CD, ............a funny man. :P


Those bump stops of yours working OK????, I made a set out of a Hi density rubber mallet, cut the head away from the handle and cut off each side of the hammer head to make two 40mm high bumpstops, fitted them in the back with you-beaut doublesided tape and no more nails, they worked a treat at Levuka.

Will have the new custom rear coils in this weekend with any luck, I'll let you all know how they go :D (I'm a little excited about it)
Author:  CD [ Thu Jan 31, 2008 10:10 pm ]
Post subject: 
cmohr wrote:
Your a funny man CD, ............a funny man. :P


Those bump stops of yours working OK????, I made a set out of a Hi density rubber mallet, cut the head away from the handle and cut off each side of the hammer head to make two 40mm high bumpstops, fitted them in the back with you-beaut doublesided tape and no more nails, they worked a treat at Levuka.

Will have the new custom rear coils in this weekend with any luck, I'll let you all know how they go :D (I'm a little excited about it)


:lol: One of the owners was at out the front on a fork when i was leaving yesterday, so I thought ............. what if.... :D

Bump stop: That's different cmohr, sounds like it worked very well. Mine are 20mm thick polyurethane (I think), there is no compression or give in them at all. Which is good, as 20mm wouldn't be enough if it was rubber. Yes, they work well but could probably be another 5mm thicker.

I will be looking at LOST on Sat night to see if you post any pics of your new springs (Let me know where you post if not Downunder). Do they have a higher rating or longer or...... or...... I will probably have to wait and see what you say on Sat or Sun (if you do the install). It will be great to maintain a good lift in the back while fully loaded. Looking forward to it mate.
Author:  CD [ Thu Jan 31, 2008 10:11 pm ]
Post subject: 
dloc_jeep_KJ wrote:
yeah take it off!!! no pun intended. :lol: :oops: :P anyways yeah it will make a diff.


:lol: With how hot it was yesterday, I could have considered taking it off :lol: :lol: Cooler today with lots of rain.
Author:  dloc_jeep_KJ [ Thu Jan 31, 2008 11:39 pm ]
Post subject: 
CDKJ wrote:
dloc_jeep_KJ wrote:
yeah take it off!!! no pun intended. :lol: :oops: :P anyways yeah it will make a diff.


:lol: With how hot it was yesterday, I could have considered taking it off :lol: :lol: Cooler today with lots of rain.


It’s just 4 bolts for the rear. They are a little bit of PITA to get to but not to bad just kind awkward. I couldn’t even tell it was off on the road either but defiantly could tell a difference in flex
Author:  DarbyWalters [ Fri Feb 01, 2008 6:58 am ]
Post subject: 
You could get your Ramp Travel Index Score if you knew how high that rear tire went:
http://www.4lo.com/calc/rticalc.htm
Page 1 of 1 All times are UTC - 5 hours [ DST ]
Powered by phpBB © 2000, 2002, 2005, 2007 phpBB Group
http://www.phpbb.com/