LOST JEEPS
http://www.lostjeeps.com/forum/phpBB3/

i think i found an axle atlast
http://www.lostjeeps.com/forum/phpBB3/viewtopic.php?f=73&t=38932		 Page 1 of 1
Author:  wolfman1722 [ Tue Jan 06, 2009 5:04 am ]
Post subject:  i think i found an axle atlast
i found someone parting out a 2000 xj is that one with the hp dana30
Author:  ohv_kj [ Tue Jan 06, 2009 10:59 am ]
Post subject: 
you might want to get the rear for the axle shafts also...you never know
Author:  JJsTJ [ Tue Jan 06, 2009 1:49 pm ]
Post subject: 
Pretty sure most of the late model XJ's came w/ the Low Pinion D30. They started putting the LP's in the TJ's in 97 and they started trickling into the XJ's a couple years later. (IIRC) Better check it to make sure.
Author:  Inc [ Tue Jan 06, 2009 2:56 pm ]
Post subject: 
I'm pretty sure 2000 were low pinion 30s.
Author:  Rock Lizard [ Tue Jan 06, 2009 3:32 pm ]
Post subject: 
Yep, low pinion in 2000-01 XJ's. 97-99 are the years you want for the HPD30 with the stronger 297 UJoints.
Author:  tjkj2002 [ Tue Jan 06, 2009 10:19 pm ]
Post subject: 
ohv_kj wrote:
you might want to get the rear for the axle shafts also...you never know
The rear axle shafts will not fit in a KJ's 8.25(to short).There are about 5 different length's for the 8.25 axles and they all are in different vehicles and being a C-clip axle you need the correct axles to work.
Author:  wolfman1722 [ Wed Jan 07, 2009 12:53 am ]
Post subject:  darn
i guess ill keep looking
Author:  Quicksilversurf917 [ Wed Jan 07, 2009 2:47 pm ]
Post subject: 
so what your saying is that I could get a 97 xj front axle and be able to swap that out for my ifs? I know someone around here who is scrapping his and I might try and jump on it
Author:  jsc7002 [ Wed Jan 07, 2009 3:47 pm ]
Post subject: 
Quicksilversurf917 wrote:
so what your saying is that I could get a 97 xj front axle and be able to swap that out for my ifs? I know someone around here who is scrapping his and I might try and jump on it


there is a little more involved than just swapping out the D30a for the HP D30, you will need custom brackets new shocks, coils, the HP D30 is just the start for a SFA
Author:  Quicksilversurf917 [ Wed Jan 07, 2009 4:53 pm ]
Post subject: 
Oh hi jsc :) long time no talk lol

yea I have been reading alot on the sfa thread and I kno I have alot to go still lol but I was jw if that was a good start
Author:  jsc7002 [ Wed Jan 07, 2009 5:04 pm ]
Post subject: 
ya the HP D30 is a good start I'm always looking for one cheap, either from a part out on a XJ or Ive thought about buying an XJ but then I wouldn't want to tear it apart for my KJ, Id end up building another rig :roll:
Page 1 of 1 All times are UTC - 5 hours [ DST ]
Powered by phpBB © 2000, 2002, 2005, 2007 phpBB Group
http://www.phpbb.com/