ha ha...
this post kinda cracks me up because I KNOW that mine are rubbing at full lock!
heres how you know:
does it sound like this?
CLACK CLACK CLACK GGGGRRRRRRRRRRRRRCCKCKCKCKCKCKCKCKKC
| LOST JEEPS http://www.lostjeeps.com/forum/phpBB3/ |
|
| How to tell if its rubbing? http://www.lostjeeps.com/forum/phpBB3/viewtopic.php?f=8&t=24861 |
Page 1 of 2 |
| Author: | hyedipin [ Sat Sep 29, 2007 8:45 pm ] |
| Post subject: | How to tell if its rubbing? |
I think my new tires are rubbing at full turn. It is slight rub, just a bit more than what you would call "minor". How can I tell? Do I charcoal it up? Or is there another trick? I had my wife drive it over to the sidewalk and driveway and I noticed it is touching when it hits the bump, I am afraid it is gonna eat it up. |
|
| Author: | tommudd [ Sat Sep 29, 2007 8:50 pm ] |
| Post subject: | |
Charcoal it up?? You should be able to tell where it is rubbing by it being shiney where its hitting/rubbing at. It will be shiney no matter if metal or plastic. Can you tell where it is for sure? Tom |
|
| Author: | jerbacher [ Sat Sep 29, 2007 9:08 pm ] |
| Post subject: | |
ha ha... this post kinda cracks me up because I KNOW that mine are rubbing at full lock!
heres how you know: does it sound like this? CLACK CLACK CLACK GGGGRRRRRRRRRRRRRCCKCKCKCKCKCKCKCKKC
|
|
| Author: | tommudd [ Sat Sep 29, 2007 9:17 pm ] |
| Post subject: | |
Hey thats what Seans was sounding like before cutting started! 
|
|
| Author: | hyedipin [ Sat Sep 29, 2007 9:19 pm ] |
| Post subject: | |
That's the thing. It is rubbing only under certain conditions. At full lock or when I am riding over bumps while turning. When I turn and stop, and look, it is so close, it is impossible to rub. So I assume it will be OK. I checked the wheel wells and there are two lines right above the fog light cover. In the morning when I get out of the parking spot and make a U turn I can hear it makes the sound you mentioned.. It is a jeep thing, hard to explain... Just like everything else, this is not consistent with rest of the stuff... |
|
| Author: | tommudd [ Sat Sep 29, 2007 10:27 pm ] |
| Post subject: | |
If its "grabbing" the plastic then you may have to do something, but just rubbing some and it doesnt bug you to much just listen and know that your tires are turning. You could heat the plastic up some and push it back just a little though and should take care of it.
|
|
| Author: | hyedipin [ Sat Sep 29, 2007 10:31 pm ] |
| Post subject: | |
tommudd wrote: If its "grabbing" the plastic then you may have to do something, but just rubbing some and it doesnt bug you to much just listen and know that your tires are turning.
You could heat the plastic up some and push it back just a little though and should take care of it.That sounds like a good idea, That inner portion is already flexible, just need to make it a bit more flexible. Is there such a thing as 1/2 inch lift or spacer that won't weaken the stability of the jeep? |
|
| Author: | hyedipin [ Sat Sep 29, 2007 10:34 pm ] |
| Post subject: | |
tommudd wrote: If its "grabbing" the plastic then you may have to do something, but just rubbing some and it doesnt bug you to much just listen and know that your tires are turning.
You could heat the plastic up some and push it back just a little though and should take care of it.That sounds like a good idea, That inner portion is already flexible, just need to make it a bit more flexible. Is there such a thing as 1/2 inch lift or spacer that won't weaken the stability of the jeep? |
|
| Author: | tommudd [ Sat Sep 29, 2007 10:39 pm ] |
| Post subject: | |
It may still rub even if you lift it , just depends on where it is? If you can get a pic maybe of the "spot" Still think that heating it up would work the best..that is if you have a heat gun. |
|
| Author: | jerbacher [ Sat Sep 29, 2007 10:44 pm ] |
| Post subject: | |
man, the heat gun method really didnt work for me. just cant move it enough to clear these tires... time to get out the dremel i think. |
|
| Author: | tommudd [ Sat Sep 29, 2007 11:22 pm ] |
| Post subject: | |
Easy way to do it (if you want to cut it) is heat it up some with the heat gun, then take a carpet knife or whatever knife and slice through, cuts like butter gives you a nice clean cut very easy to do |
|
| Author: | hyedipin [ Sat Sep 29, 2007 11:25 pm ] |
| Post subject: | |
cut what? wheel well!? Or are you talking about the little fin shaped plastic. |
|
| Author: | jerbacher [ Sat Sep 29, 2007 11:30 pm ] |
| Post subject: | |
hyedipin wrote: cut what? wheel well!? Or are you talking about the little fin shaped plastic.
the wheel well liner around the fog light door |
|
| Author: | hyedipin [ Sun Sep 30, 2007 12:15 am ] |
| Post subject: | |
will post pix tomorrow. |
|
| Author: | tommudd [ Sun Sep 30, 2007 12:57 am ] |
| Post subject: | |
Cool post pics of where then we can determine what would work best for ya! Tom |
|
| Author: | Fulltimer [ Sun Sep 30, 2007 4:36 am ] |
| Post subject: | |
hyedipin wrote: cut what? wheel well!? Or are you talking about the little fin shaped plastic.
The fin shaped piece is covering the pinch weld. Terry |
|
| Author: | hyedipin [ Sun Sep 30, 2007 11:36 am ] |
| Post subject: | |
Fulltimer wrote: hyedipin wrote: cut what? wheel well!? Or are you talking about the little fin shaped plastic. The fin shaped piece is covering the pinch weld. Terry yes, pinch weld, ah It was right at the edge of my tongue.. thanks! |
|
| Author: | _UnLiMiTeD_ [ Sun Sep 30, 2007 1:45 pm ] |
| Post subject: | |
aint no carpenter knife in the world gunna cut that pinch weld lol |
|
| Author: | hyedipin [ Sun Sep 30, 2007 2:09 pm ] |
| Post subject: | |
|
|
| Author: | Fulltimer [ Sun Sep 30, 2007 2:17 pm ] |
| Post subject: | |
Yep, it's rubbing. Terry |
|
| Page 1 of 2 | All times are UTC - 5 hours [ DST ] |
| Powered by phpBB © 2000, 2002, 2005, 2007 phpBB Group http://www.phpbb.com/ |
|