Should have no issues then
I'll try and find a couple of pictures for ya
| LOST JEEPS http://www.lostjeeps.com/forum/phpBB3/ |
|
| Anyone running 255/70/16's on Moabs? http://www.lostjeeps.com/forum/phpBB3/viewtopic.php?f=8&t=71674 |
Page 1 of 1 |
| Author: | glaspak845 [ Sun Sep 16, 2012 11:02 pm ] |
| Post subject: | Anyone running 255/70/16's on Moabs? |
Curious is anyone is running this setup and will it/does it minimize rubbing? Thanks, Mike |
|
| Author: | tommudd [ Mon Sep 17, 2012 12:47 am ] |
| Post subject: | Re: Anyone running 255/70/16's on Moabs? |
Ran them for a while are you lifted ? |
|
| Author: | glaspak845 [ Tue Sep 18, 2012 7:03 pm ] |
| Post subject: | Re: Anyone running 255/70/16's on Moabs? |
Yeah, OME lift. HD springs up front, MED spring rate in rear. OME shocks and struts as well. |
|
| Author: | tommudd [ Tue Sep 18, 2012 7:32 pm ] |
| Post subject: | Re: Anyone running 255/70/16's on Moabs? |
Should have no issues then I'll try and find a couple of pictures for ya
|
|
| Author: | ATXKJ [ Tue Sep 18, 2012 8:49 pm ] |
| Post subject: | Re: Anyone running 255/70/16's on Moabs? |
depending on the tread width (different from section width) you might end up hammering down a pinch weld and clearing up some of the front wheel well liner or it may clear with no issues...... normally 255's are not a problem. |
|
| Author: | glaspak845 [ Tue Sep 18, 2012 10:08 pm ] |
| Post subject: | Re: Anyone running 255/70/16's on Moabs? |
Thanks for the advice. I currently have 245/75/16's on the Moabs now and they rub on both the lower front bumper trim strip and the pinch weld, or at least the inner fender liner over the welds. I have to look at them some more. Another question, what tire pressure do people run the tires at? I know the max is 80 psi on the MT/R's I have on there now. Usually, with the previous tires the max was 50 psi and I ran them around 45 psi cold. Thanks. |
|
| Author: | Voyager [ Wed Sep 19, 2012 8:46 am ] |
| Post subject: | Re: Anyone running 255/70/16's on Moabs? |
glaspak845 wrote: Thanks for the advice. Hey! I see you're from Allentown. Howdy neighbor!!! 
|
|
| Author: | glaspak845 [ Sat Sep 22, 2012 3:43 pm ] |
| Post subject: | Re: Anyone running 255/70/16's on Moabs? |
Here's a pic with the wheels and tires mounted on the jeep. Moabs with 245/75/16 Goodyear MT/R's on them. 
|
|
| Author: | TwoBobsKJ [ Thu Sep 27, 2012 10:46 pm ] |
| Post subject: | Re: Anyone running 255/70/16's on Moabs? |
I run 255/70-16's on stock Renegade wheels. No rub except in reverse at full lock on the edge of the front air dam. Lifted sitting at 22.25 front, 22.5 rear with OME 927/948, 1/4" top plate, 3/8" clevis and one extra rear iso. You should be OK but with the backspacing difference I don't know if you'd catch the fog light door and/or the pinch weld cuz of the wider arc.   Bob |
|
| Page 1 of 1 | All times are UTC - 5 hours [ DST ] |
| Powered by phpBB © 2000, 2002, 2005, 2007 phpBB Group http://www.phpbb.com/ |
|