LOST JEEPS
http://www.lostjeeps.com/forum/phpBB3/

Lift kit selection - help
http://www.lostjeeps.com/forum/phpBB3/viewtopic.php?f=88&t=78570
Page 1 of 2

Author:  nabeelferzan [ Thu Mar 13, 2014 12:43 pm ]
Post subject:  Lift kit selection - help

Hi,
I am planning to lift my 2008 Jeep Cherokee/Liberty 3.7L (KK) and have finally selected the below two options.
I will need some help in deciding which one to go for since this will be the first time i will be doing it.

I have been offered the following.
(a) Ironman suspension lift kit for Jeep KK that give me a minimum 40mm lift.
(b) Dobinsons suspension lift kit for Jeep KK that also gives me a minimum of 40mm lift.
Pricing wise both are falling on the same area with the Ironman locally available and the Dobinsons having to be ordered in from Australia.
I would like fellow KK'ers who have any experience with the above lifts to give me the pros and cons on the suspension kits.
Any information is appreciated. Thanks in advance.
Nabeel.

Author:  huntb [ Thu Mar 13, 2014 1:38 pm ]
Post subject:  Re: Lift kit selection - help

nabeelferzan wrote:
Hi,
I am planning to lift my 2008 Jeep Cherokee/Liberty 3.7L (KK) and have finally selected the below two options.
I will need some help in deciding which one to go for since this will be the first time i will be doing it.

I have been offered the following.
(a) Ironman suspension lift kit for Jeep KK that give me a minimum 40mm lift.
(b) Dobinsons suspension lift kit for Jeep KK that also gives me a minimum of 40mm lift.
Pricing wise both are falling on the same area with the Ironman locally available and the Dobinsons having to be ordered in from Australia.
I would like fellow KK'ers who have any experience with the above lifts to give me the pros and cons on the suspension kits.
Any information is appreciated. Thanks in advance.
Nabeel.


Ironman doesn't make rear springs for the KK, but the rest of the components are top notch

Author:  Bmxer524 [ Thu Mar 13, 2014 1:57 pm ]
Post subject:  Re: Lift kit selection - help

I never heard of Dobinsons, so I would go Ironman...

Author:  nabeelferzan [ Thu Mar 13, 2014 3:01 pm ]
Post subject:  Re: Lift kit selection - help

huntb wrote:
nabeelferzan wrote:
Hi,
I am planning to lift my 2008 Jeep Cherokee/Liberty 3.7L (KK) and have finally selected the below two options.
I will need some help in deciding which one to go for since this will be the first time i will be doing it.

I have been offered the following.
(a) Ironman suspension lift kit for Jeep KK that give me a minimum 40mm lift.
(b) Dobinsons suspension lift kit for Jeep KK that also gives me a minimum of 40mm lift.
Pricing wise both are falling on the same area with the Ironman locally available and the Dobinsons having to be ordered in from Australia.
I would like fellow KK'ers who have any experience with the above lifts to give me the pros and cons on the suspension kits.
Any information is appreciated. Thanks in advance.
Nabeel.


Ironman doesn't make rear springs for the KK, but the rest of the components are top notch


I did check out their website and they do have a specific kit for KK and KJ. The rear springs could be the same for KK and KJ I suppose.

Author:  LKWJeeper [ Thu Mar 13, 2014 3:06 pm ]
Post subject:  Re: Lift kit selection - help

If you're going to ship from Australia I'd look at Murchison products. They make some cool stuff. Too expensive to ship to the US

Sent from my LG-D801 using Tapatalk

Author:  huntb [ Thu Mar 13, 2014 3:17 pm ]
Post subject:  Re: Lift kit selection - help

nabeelferzan wrote:
huntb wrote:
nabeelferzan wrote:
Hi,
I am planning to lift my 2008 Jeep Cherokee/Liberty 3.7L (KK) and have finally selected the below two options.
I will need some help in deciding which one to go for since this will be the first time i will be doing it.

I have been offered the following.
(a) Ironman suspension lift kit for Jeep KK that give me a minimum 40mm lift.
(b) Dobinsons suspension lift kit for Jeep KK that also gives me a minimum of 40mm lift.
Pricing wise both are falling on the same area with the Ironman locally available and the Dobinsons having to be ordered in from Australia.
I would like fellow KK'ers who have any experience with the above lifts to give me the pros and cons on the suspension kits.
Any information is appreciated. Thanks in advance.
Nabeel.


Ironman doesn't make rear springs for the KK, but the rest of the components are top notch


I did check out their website and they do have a specific kit for KK and KJ. The rear springs could be the same for KK and KJ I suppose.


The rear springs for the KK are definitely not the same as the rear springs for the KJ. Do you have a link to the page that is telling you this?

Author:  Bmxer524 [ Thu Mar 13, 2014 3:27 pm ]
Post subject:  Re: Lift kit selection - help

This is their Liberty catalogue: http://www.ironman4x4.com/html/jeep/25.html

Says springs and kits are only for KJs. You can run Ironman shocks, and front springs. You're just going to have to find different rear springs.

I know you're not in the US, so I don't know what shipping is like for you, nor what is readily available. I say go JBA 4" rear spings and make the Tommudd econo lift, or OME. Not sure how Ironman front and OME rear would ride...

Author:  At The Helm [ Thu Mar 13, 2014 3:41 pm ]
Post subject:  Re: Lift kit selection - help

Pretty sure there are a few Old Man Emu distributors in Dubai. I also know of someone who bought a set of my bumpers in Dubai but totaled his KK before they could be installed...

Author:  Cherrie 274 [ Thu Mar 13, 2014 3:56 pm ]
Post subject:  Re: Lift kit selection - help

Atthehelm wrote:
Pretty sure there are a few Old Man Emu distributors in Dubai. I also know of someone who bought a set of my bumpers in Dubai but totaled his KK before they could be installed...

Wow! You went international !:).

Author:  tommudd [ Thu Mar 13, 2014 4:33 pm ]
Post subject:  Re: Lift kit selection - help

To the OP
I'd look for a OME dealer, they had some there or did have, thaat or Stus lifts are just as good or better since you may have to ship from Aus.

Author:  nabeelferzan [ Fri Mar 14, 2014 8:11 am ]
Post subject:  Re: Lift kit selection - help

Bmxer524 wrote:
This is their Liberty catalogue: http://www.ironman4x4.com/html/jeep/25.html

Says springs and kits are only for KJs. You can run Ironman shocks, and front springs. You're just going to have to find different rear springs.

I know you're not in the US, so I don't know what shipping is like for you, nor what is readily available. I say go JBA 4" rear spings and make the Tommudd econo lift, or OME. Not sure how Ironman front and OME rear would ride...


Yes, their catalogue online says coils are only for KJ's. I checked with their local retailer here and they said that they have an Ironman kit for the KK also.
Not sure what they meant, will go tomorrow to their place and check it out what they have for the KK.

In the meantime, I understand that you are running OME coils and Bilstein shocks/sturts on your KK.
Can you tell me how much lift did you get with this set up?
Can you also tell me the part numbers of your OME coils and Bilstein's?
thanks,
Nabeel

Author:  nabeelferzan [ Fri Mar 14, 2014 8:20 am ]
Post subject:  Re: Lift kit selection - help

Bmxer524 wrote:
I never heard of Dobinsons, so I would go Ironman...


Dobinsons are based out of Australia. They have a kit for the KK. The link is below:
[url]http://www.dobinsonsprings.com/docs/catalogues/4x4/pdf/JEEP-59.pdf

Author:  huntb [ Fri Mar 14, 2014 9:20 am ]
Post subject:  Re: Lift kit selection - help

nabeelferzan wrote:
Bmxer524 wrote:
This is their Liberty catalogue: http://www.ironman4x4.com/html/jeep/25.html

Says springs and kits are only for KJs. You can run Ironman shocks, and front springs. You're just going to have to find different rear springs.

I know you're not in the US, so I don't know what shipping is like for you, nor what is readily available. I say go JBA 4" rear spings and make the Tommudd econo lift, or OME. Not sure how Ironman front and OME rear would ride...


Yes, their catalogue online says coils are only for KJ's. I checked with their local retailer here and they said that they have an Ironman kit for the KK also.
Not sure what they meant, will go tomorrow to their place and check it out what they have for the KK.

In the meantime, I understand that you are running OME coils and Bilstein shocks/sturts on your KK.
Can you tell me how much lift did you get with this set up?
Can you also tell me the part numbers of your OME coils and Bilstein's?
thanks,
Nabeel


The OME springs will give you about 2.5 inches (~60mm) of lift

Author:  nabeelferzan [ Fri Mar 14, 2014 9:58 am ]
Post subject:  Re: Lift kit selection - help

huntb wrote:
nabeelferzan wrote:
Bmxer524 wrote:
This is their Liberty catalogue: http://www.ironman4x4.com/html/jeep/25.html

Says springs and kits are only for KJs. You can run Ironman shocks, and front springs. You're just going to have to find different rear springs.

I know you're not in the US, so I don't know what shipping is like for you, nor what is readily available. I say go JBA 4" rear spings and make the Tommudd econo lift, or OME. Not sure how Ironman front and OME rear would ride...


Yes, their catalogue online says coils are only for KJ's. I checked with their local retailer here and they said that they have an Ironman kit for the KK also.
Not sure what they meant, will go tomorrow to their place and check it out what they have for the KK.

In the meantime, I understand that you are running OME coils and Bilstein shocks/sturts on your KK.
Can you tell me how much lift did you get with this set up?
Can you also tell me the part numbers of your OME coils and Bilstein's?
thanks,
Nabeel


The OME springs will give you about 2.5 inches (~60mm) of lift


Thanks for the info huntb.
Can you provide me with the part numbers for the OME springs and the Ironman shocks on your KK?

Author:  huntb [ Fri Mar 14, 2014 10:40 am ]
Post subject:  Re: Lift kit selection - help

Ironman front shocks: http://jeepinbyal.com/jeep-liberty-2008-2012-kk/front-struts-for-kk/ironman-front-strut.html

Ironman rear shocks: http://jeepinbyal.com/jeep-liberty-2008-2012-kk/rear-shocks-and-coil-springs/ironman-rear-shocks.html

OME front springs (either 2926 or 2927): http://jeepinbyal.com/jeep-liberty-2008-2012-kk/front-struts-for-kk/ome-front-coil-springs.html

OME rear springs (2730 if you got 2926 front or 2731 if you got 2927 front): http://jeepinbyal.com/jeep-liberty-2008-2012-kk/rear-shocks-and-coil-springs/ome-spring-for-rear-kk.html

Front Bumpstops: http://jeepinbyal.com/jeep-liberty-2008-2012-kk/front-struts-for-kk/teraflex-bump-stop.html

Rear bumpstops: Make your own out of hockey pucks or http://jeepinbyal.com/jeep-liberty-2008-2012-kk/rear-shocks-and-coil-springs/rear-bump-stop-4.html

Author:  nFodzy [ Fri Mar 14, 2014 1:47 pm ]
Post subject:  Re: Lift kit selection - help

huntb wrote:


Hunt, is this your exact set up? How do you like the ride?

Author:  Bmxer524 [ Fri Mar 14, 2014 2:43 pm ]
Post subject:  Re: Lift kit selection - help

nabeelferzan wrote:
Bmxer524 wrote:
This is their Liberty catalogue: http://www.ironman4x4.com/html/jeep/25.html

Says springs and kits are only for KJs. You can run Ironman shocks, and front springs. You're just going to have to find different rear springs.

I know you're not in the US, so I don't know what shipping is like for you, nor what is readily available. I say go JBA 4" rear spings and make the Tommudd econo lift, or OME. Not sure how Ironman front and OME rear would ride...


Yes, their catalogue online says coils are only for KJ's. I checked with their local retailer here and they said that they have an Ironman kit for the KK also.
Not sure what they meant, will go tomorrow to their place and check it out what they have for the KK.

In the meantime, I understand that you are running OME coils and Bilstein shocks/sturts on your KK.
Can you tell me how much lift did you get with this set up?
Can you also tell me the part numbers of your OME coils and Bilstein's?
thanks,
Nabeel


If you go with 927/731 springs(front and rear respectively) you'll get abour 2.5" of lift. Don't have part numbers for my Bilsteins, but I'm sure they're somewhere on this forum. As for my lift, I added a few extras to get about 3.5" of lift.

Author:  nabeelferzan [ Sat Mar 15, 2014 2:56 pm ]
Post subject:  Re: Lift kit selection - help

huntb wrote:


Thanks for the details huntb. Are you using the following Ironman shocks on your setup?
Front: Ironman Nitro Gas 12711GR
Rear: Ironman Nitro Gas 12712GR


Sent from my iPad using Tapatalk

Author:  nabeelferzan [ Sat Mar 15, 2014 3:08 pm ]
Post subject:  Re: Lift kit selection - help

Bmxer524 wrote:
nabeelferzan wrote:
Bmxer524 wrote:
This is their Liberty catalogue: http://www.ironman4x4.com/html/jeep/25.html

Says springs and kits are only for KJs. You can run Ironman shocks, and front springs. You're just going to have to find different rear springs.

I know you're not in the US, so I don't know what shipping is like for you, nor what is readily available. I say go JBA 4" rear spings and make the Tommudd econo lift, or OME. Not sure how Ironman front and OME rear would ride...


Yes, their catalogue online says coils are only for KJ's. I checked with their local retailer here and they said that they have an Ironman kit for the KK also.
Not sure what they meant, will go tomorrow to their place and check it out what they have for the KK.

In the meantime, I understand that you are running OME coils and Bilstein shocks/sturts on your KK.
Can you tell me how much lift did you get with this set up?
Can you also tell me the part numbers of your OME coils and Bilstein's?
thanks,
Nabeel


If you go with 927/731 springs(front and rear respectively) you'll get abour 2.5" of lift. Don't have part numbers for my Bilsteins, but I'm sure they're somewhere on this forum. As for my lift, I added a few extras to get about 3.5" of lift.


Thanks Bmxer524 for the info on the springs. I am finding it difficult to source the OME springs here in the UAE, still checking though! The KK is not a very popular 4x4 here in the UAE, so retailers don't stock aftermarket parts much. :(
I read through your earlier posts and see that you have mentioned the following part numbers for the Bilsteins.
Can you confirm the below?
Front: Bilstein 24-139168
Rear: Bilstein 33-185552


Sent from my iPad using Tapatalk

Author:  huntb [ Sat Mar 15, 2014 5:49 pm ]
Post subject:  Re: Lift kit selection - help

nFodzy wrote:


I got OME springs before they changed the part numbers. I have HD up front and MD in the rear. I also have a clevis lift, top plates, JBA A-arms, extra isos in the rear and extended rear sway bar links. I love the ride but I'm going to replace the rear Ironman shocks with the longer 4" Ironman shocks this summer since I added 2 extra isos per side

Page 1 of 2 All times are UTC - 5 hours [ DST ]
Powered by phpBB © 2000, 2002, 2005, 2007 phpBB Group
http://www.phpbb.com/