| LOST JEEPS http://www.lostjeeps.com/forum/phpBB3/ |
|
| PLEASEEE HELP WITH MI LIFT!!!! http://www.lostjeeps.com/forum/phpBB3/viewtopic.php?f=88&t=78700 |
Page 1 of 1 |
| Author: | onil182 [ Tue Mar 25, 2014 9:55 pm ] |
| Post subject: | PLEASEEE HELP WITH MI LIFT!!!! |
Hi guys I had a KK With this setup: Front: OME 2927 OME 90009 Rear: OME 2731 OME 132L I wanted to go with more lift so I added Front: JBA Top spacer plate Clevis Spacer 0.735 JBA UCA´s Rear: Two Isos per side But today when I went to pick up my car after installing all of that, the handling was awful and the car was WAAAAYY Higher in the front than in the back. Do you have any ideas of what might have gone wrong?? please help!!! |
|
| Author: | nFodzy [ Tue Mar 25, 2014 10:24 pm ] |
| Post subject: | Re: PLEASEEE HELP WITH MI LIFT!!!! |
onil182 wrote: Hi guys I had a KK With this setup: Front: OME 2927 OME 90009 Rear: OME 2731 OME 132L I wanted to go with more lift so I added Front: JBA Top spacer plate Clevis Spacer 0.735 JBA UCA´s Rear: Two Isos per side But today when I went to pick up my car after installing all of that, the handling was awful and the car was WAAAAYY Higher in the front than in the back. Do you have any ideas of what might have gone wrong?? please help!!! Pictures? Curious to see how much higher the front is.. |
|
| Author: | At The Helm [ Tue Mar 25, 2014 11:19 pm ] |
| Post subject: | Re: PLEASEEE HELP WITH MI LIFT!!!! |
Right after r & i ing the front suspension its going be a bit higher because they components haven't settled in. The handling on the drive home probably felt weird because its now out of alignment... What are the measurements from the center of the wheels to the bottom of the fender flares? |
|
| Author: | At The Helm [ Wed Mar 26, 2014 1:12 am ] |
| Post subject: | Re: PLEASEEE HELP WITH MI LIFT!!!! |
Also I'm guessing you meant .375 (Decimal equivilant to 3/8") instead of .735 |
|
| Author: | Bmxer524 [ Wed Mar 26, 2014 1:20 am ] |
| Post subject: | Re: PLEASEEE HELP WITH MI LIFT!!!! |
Atthehelm wrote: Also I'm guessing you meant .375 (Decimal equivilant to 3/8") instead of .735 That's what Tom and I were hoping in his post of JF. Measurements would help, but biggest thing is an alignment, assuming the lift is installed correctly and the clevis lift is a typo(meaning it's a 3/8" clevis instead of 3/4"). Alignment will help drop the front some, it helps with CV angles(depending on height, they might be crying lol I know mine were when I first installed the 927, top plate and 3/8" clevis lift, the alignment fixed it), and will fix your handling problems. |
|
| Author: | tommudd [ Wed Mar 26, 2014 7:46 am ] |
| Post subject: | Re: PLEASEEE HELP WITH MI LIFT!!!! |
Plus he installed new UCAs so hoping he tightened those after full weight on the ground. If he didn't that would cause issues as well at first |
|
| Page 1 of 1 | All times are UTC - 5 hours [ DST ] |
| Powered by phpBB © 2000, 2002, 2005, 2007 phpBB Group http://www.phpbb.com/ |
|