LOST JEEPS
http://www.lostjeeps.com/forum/phpBB3/

Gibson exhaust install
http://www.lostjeeps.com/forum/phpBB3/viewtopic.php?f=88&t=79621		 Page 1 of 1
Author:  ajohns1288 [ Mon Jul 14, 2014 9:34 pm ]
Post subject:  Gibson exhaust install
Has anyone installed this on a KK? It mentions to bolt to a flange right after the cat, however I just have a clamp in the area pictured. All of the pictures and topics I could find were KJs. I figure I just ditch the flange and just use the clamp, right? It says it is compatible with 2008 KK, but I want to make sure before I open the box in case I need to return in.
Author:  Gageraid [ Mon Jul 14, 2014 9:42 pm ]
Post subject:  Re: Gibson exhaust install
ajohns1288 wrote:
Has anyone installed this on a KK? It mentions to bolt to a flange right after the cat, however I just have a clamp in the area pictured. All of the pictures and topics I could find were KJs. I figure I just ditch the flange and just use the clamp, right? It says it is compatible with 2008 KK, but I want to make sure before I open the box in case I need to return in.


Yup it works. So easy that even did it myself.
Author:  ajohns1288 [ Tue Jul 15, 2014 10:36 am ]
Post subject:  Re: Gibson exhaust install
Nice, I was hoping it was that easy. I'll probably do it in my driveway this weekend.
Author:  lammarco [ Tue Jul 15, 2014 9:09 pm ]
Post subject:  Re: Gibson exhaust install
ajohns1288 wrote:
Nice, I was hoping it was that easy. I'll probably do it in my driveway this weekend.

Just use the ramp and you can do it in few hours. You need to cut the old pipe...and it's not easy to install the hanger at the rear...I used WD40 and it will go right in...
Author:  Gageraid [ Tue Jul 15, 2014 10:18 pm ]
Post subject:  Re: Gibson exhaust install
lammarco wrote:
ajohns1288 wrote:
Nice, I was hoping it was that easy. I'll probably do it in my driveway this weekend.

Just use the ramp and you can do it in few hours. You need to cut the old pipe...and it's not easy to install the hanger at the rear...I used WD40 and it will go right in...


It was really easy for me. I'd say it took about an hour. I wasn't that thrilled I had to cut the old exhaust off, but I think it's the only way.
Author:  lammarco [ Wed Jul 16, 2014 4:27 pm ]
Post subject:  Re: Gibson exhaust install
Gageraid wrote:
lammarco wrote:
ajohns1288 wrote:
Nice, I was hoping it was that easy. I'll probably do it in my driveway this weekend.

Just use the ramp and you can do it in few hours. You need to cut the old pipe...and it's not easy to install the hanger at the rear...I used WD40 and it will go right in...


It was really easy for me. I'd say it took about an hour. I wasn't that thrilled I had to cut the old exhaust off, but I think it's the only way.


AGREE! Just make sure you don't cut too much of the old old pipe...Otherwise it will be FUN to install the tail pipe! :dead:

Good luck!
Author:  ajohns1288 [ Sat Jul 19, 2014 2:07 pm ]
Post subject:  Re: Gibson exhaust install
lammarco wrote:
Gageraid wrote:
lammarco wrote:
Just use the ramp and you can do it in few hours. You need to cut the old pipe...and it's not easy to install the hanger at the rear...I used WD40 and it will go right in...


It was really easy for me. I'd say it took about an hour. I wasn't that thrilled I had to cut the old exhaust off, but I think it's the only way.


AGREE! Just make sure you don't cut too much of the old old pipe...Otherwise it will be FUN to install the tail pipe! :dead:

Good luck!


Does anyone happen to have a picture of where the cut is at? Is it rear or forward of the little bend between the muffler and crossover? Either way, at least by cutting you don't have to worry about getting the clamp off. I don't know if there's any amount of PB blaster that will get the bolt on mine un-seized.
Author:  Gageraid [ Sat Jul 19, 2014 7:55 pm ]
Post subject:  Re: Gibson exhaust install
I'll check right now if I have a picture.
EDIT: Couldn't find the picture. Cut whatever you have to in order to get it off.
Author:  lammarco [ Sun Jul 20, 2014 10:30 am ]
Post subject:  Re: Gibson exhaust install
You cut the front...b/c the cat has a little extension in front of it...I cut the exhaust into 2 parts...I cut the rear pipe between gas tank and rear suspension so that you can remove the muffler...then cut off the cat... That's how I did mine...
Page 1 of 1 All times are UTC - 5 hours [ DST ]
Powered by phpBB © 2000, 2002, 2005, 2007 phpBB Group
http://www.phpbb.com/