I've looked at General's site and through a number of vendor's pages and still can't seem to find out if the General Grabber AT2's have a 2 or 3 ply sidewall.

_________________
2007 KJ Limited 4x4

29G, Tow pkg, full skids, bun warmers, moon roof
Amsoil Air Filter, CB, custom cargo box
OME / Rancho Lift / Rockcrusher rear Diff Cover / Super Skink Sliders (not installed yet)
245/75R16 GY MT/R's with Crager 16 x 8 x 5" BS wheels
L.O.S.T. # 005465

just went out and looked at mine and they are 2 ply sidewalls and 2x2x2 treads

_________________
2003 Jeep LIberty Renegade
Rusty's Offroad 2.5in suspension lift w/ rear rancho shocks, Fastman TB, Beam's 4 point harness', custom D rings up front, Custom flowmaster exhaust, JKS Quick sway bar disco's
Hella 500's, General Grabber AT2's on stock rims with spidertrax
coming soon: Corbeau Moab seats, JBA 6"lift

Thanks for the info C of C.

_________________
2007 KJ Limited 4x4

29G, Tow pkg, full skids, bun warmers, moon roof
Amsoil Air Filter, CB, custom cargo box
OME / Rancho Lift / Rockcrusher rear Diff Cover / Super Skink Sliders (not installed yet)
245/75R16 GY MT/R's with Crager 16 x 8 x 5" BS wheels
L.O.S.T. # 005465

if you decide to get them; i hope yo do because they rock; mkae sure you have them balanced with glue on weights, the bead/rim protector likes to nock the hammer on ones off pretty easily

_________________
2003 Jeep LIberty Renegade
Rusty's Offroad 2.5in suspension lift w/ rear rancho shocks, Fastman TB, Beam's 4 point harness', custom D rings up front, Custom flowmaster exhaust, JKS Quick sway bar disco's
Hella 500's, General Grabber AT2's on stock rims with spidertrax
coming soon: Corbeau Moab seats, JBA 6"lift

You sure they didn't just use the wrong weights? I've never seen an issue on Grabber AT's or BFG AT's where the tire actually causes the weight to come off. the tape weights are a pain in the booty.

Just get them balanced with the little beads that go inside the tire. I had my new Silent Armors balanced that way and it's perfect. No weights on the rims at all, and never have to be balanced again.

_________________
June 2001 Liberty Limited 4X4
Frankenlift II Premium, Al's Upper Arms, 245/75R16 C Silent Armors on Moabs, RL Skink Super Sliders, Rear DTT, Riddler Diff Cover, Fastman Throttle Body, Profinish-Proglass Hood, Borla Dual Outlet Exhaust, TransGo Reprogramming Kit, APS Stall Converter, 4.10 Gears, B&G Chrysler PCM, Lots of Line-X, etc...

ky ive been meaning to asky you something. Your borla exhaust pipe that come out the drivers side on the rearend hangs pretty low by the rear diff. How are you not scared about tearing it off on a rock?

_________________
2003 Jeep LIberty Renegade
Rusty's Offroad 2.5in suspension lift w/ rear rancho shocks, Fastman TB, Beam's 4 point harness', custom D rings up front, Custom flowmaster exhaust, JKS Quick sway bar disco's
Hella 500's, General Grabber AT2's on stock rims with spidertrax
coming soon: Corbeau Moab seats, JBA 6"lift

Little off topic, but my Jeep isn't used on trails. The only way the exhaust will get hit right now is if there is something really big in the road. The muffler is actually the lowest hanging part. I'm going to change the exhaust out if I go with the RL rear bumper because it will hang way below that bumper. I'll also change it out if this Jeep becomes a trail rig.

_________________
June 2001 Liberty Limited 4X4
Frankenlift II Premium, Al's Upper Arms, 245/75R16 C Silent Armors on Moabs, RL Skink Super Sliders, Rear DTT, Riddler Diff Cover, Fastman Throttle Body, Profinish-Proglass Hood, Borla Dual Outlet Exhaust, TransGo Reprogramming Kit, APS Stall Converter, 4.10 Gears, B&G Chrysler PCM, Lots of Line-X, etc...