It is currently Sat Nov 22, 2025 11:06 am

All times are UTC - 5 hours [ DST ]




Post new topic Reply to topic  [ 6 posts ] 
Author Message
 Post subject: relay/fuse clarification
PostPosted: Wed Mar 30, 2011 5:17 pm 
Offline
LOST Junkie
User avatar

Joined: Sat Oct 02, 2010 7:33 pm
Posts: 552
Location: Long Island
r36 would be the viscous heater relay, im looking to pull it for improved mpgs, or at least to see if it improves mpgs. Dont mind the cold i never use the heat unless its reallly cold anyway. And also fuse 38(red 10 amp) would be the one to turn ABS off right? I assume this would turn off the rear electronic locker crap this thing has. Its irritating because it wears the rear brakes out like crazy, and now they squeek and it pisses me off :evil: . Thanks!

_________________
06 CRD limited
Frankenlift, JBA 1/4 top plate, 3 clevis rings, 3 stacked iso's
JBA UCA and quick disconnects
Procomp rockkrawlr 16x8 4.25bs with 265-70-65 General Grabber AT2's
Mopar full skid plates, JCR stage 3 Rock Rails
Kenwood HU, 6.5 pioneer marine grade door speakers, JL stealthbox kenwood amp
GDE HOT tune
Soon to come
RL Rock monitor bumper


Top
 Profile  
 
 Post subject: Re: relay/fuse clarification
PostPosted: Wed Mar 30, 2011 9:52 pm 
Offline
Lifetime Member
Lifetime Member
User avatar

Joined: Tue Sep 22, 2009 10:16 pm
Posts: 3059
Location: Oxford, Connecticut
I saw pull the fuses out and give it a shot..... see how it works for you.

_________________
2006 Liberty Limited CRD, Deep Beryl Green, Yeti tune, Arp studs, new cams, rockers, lifters, TB. "Green Monster"
2005 Liberty Sport CRD, Deep Beryl Green, GDE Hot Tune, ARP studs. "Rocket"
1982 Fiat 124 Spider Convertible. "Fiona"


Top
 Profile  
 
 Post subject: Re: relay/fuse clarification
PostPosted: Wed Mar 30, 2011 10:04 pm 
Offline
LOST Junkie
User avatar

Joined: Sat Oct 02, 2010 7:33 pm
Posts: 552
Location: Long Island
the thing is, i never notice when the viscous is on or off.. so that ones hard for me to tell. The ABS one i'll try eventually. The viscous relay out shouldnt give me a check engine light or anything would it?

_________________
06 CRD limited
Frankenlift, JBA 1/4 top plate, 3 clevis rings, 3 stacked iso's
JBA UCA and quick disconnects
Procomp rockkrawlr 16x8 4.25bs with 265-70-65 General Grabber AT2's
Mopar full skid plates, JCR stage 3 Rock Rails
Kenwood HU, 6.5 pioneer marine grade door speakers, JL stealthbox kenwood amp
GDE HOT tune
Soon to come
RL Rock monitor bumper


Top
 Profile  
 
 Post subject: Re: relay/fuse clarification
PostPosted: Thu Mar 31, 2011 8:20 am 
Offline
Lifetime Member
Lifetime Member

Joined: Sun Mar 28, 2010 9:15 am
Posts: 5431
Location: Tallahassee, Florida
I pulled the R36 viscous heater relay about 3 weeks ago and no codes. The relay was in there too tight to pull with fingers so I wound up lightly grasping it with pliers and it came out just fine with a bit of wiggling and an upward pull. I did put a bit of electrical tape in the bottom the relay recess to keep dust off the contacts. Cannot report on mileage yet but the EVIC, which has been more accurate after a recent update to the GDE ECO tune, reports a mpg gain if one believes the EVIC.

_________________
Sold to LOST member my 05 Ltd, GDE Stg II turbo + TCM tune, SunCoast TC w. Transgo kit, Steiger window regulators, Samcos, Fumoto valve, 2nd gen filter head with Lub. Spec. bleeder, Hayden clutch & 11 blade fan, inverted spare, P-1 battery, BF Goodrich Long Trail TAs, Etecno1 glow plugs, timing belt at 50K miles/8 yrs


Top
 Profile  
 
 Post subject: Re: relay/fuse clarification
PostPosted: Thu Mar 31, 2011 2:15 pm 
Offline
LOST Addict
User avatar

Joined: Tue Apr 03, 2007 2:07 am
Posts: 6218
Location: Colorado Baby!
irollgen4s wrote:
the thing is, i never notice when the viscous is on or off.. so that ones hard for me to tell. The ABS one i'll try eventually. The viscous relay out shouldnt give me a check engine light or anything would it?


You can pop the hood and see if the viscous heater is running.

_________________
http://www.Colorado4Wheel.com
"Its not about what you can DO with your Jeep, its about where you can GO with your Jeep."
Knowledgeable - But Caustic


Top
 Profile  
 
 Post subject: Re: relay/fuse clarification
PostPosted: Thu Mar 31, 2011 2:50 pm 
Offline
LOST Junkie
User avatar

Joined: Sat Oct 02, 2010 7:33 pm
Posts: 552
Location: Long Island
thanks guys!

_________________
06 CRD limited
Frankenlift, JBA 1/4 top plate, 3 clevis rings, 3 stacked iso's
JBA UCA and quick disconnects
Procomp rockkrawlr 16x8 4.25bs with 265-70-65 General Grabber AT2's
Mopar full skid plates, JCR stage 3 Rock Rails
Kenwood HU, 6.5 pioneer marine grade door speakers, JL stealthbox kenwood amp
GDE HOT tune
Soon to come
RL Rock monitor bumper


Top
 Profile  
 
Display posts from previous:  Sort by  
Post new topic Reply to topic  [ 6 posts ] 

All times are UTC - 5 hours [ DST ]


Who is online

Users browsing this forum: No registered users and 74 guests


You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum

Search for:
Jump to:  
Powered by phpBB © 2000, 2002, 2005, 2007 phpBB Group. Color scheme by ColorizeIt!
Logo by pixeldecals.com