** Musclez KK Arctic BUILD THREAD **

musclezmarinara · **Posted:** Tue Mar 27, 2012 11:21 am

arcticbutcher wrote:

so wish I could see these pictures!!! :furious:

check now

musclezmarinara · **Posted:** Tue Mar 27, 2012 11:21 am

arcticbutcher wrote:

so wish I could see these pictures!!! :furious:

check now

musclezmarinara · **Posted:** Tue Mar 27, 2012 11:21 am

arcticbutcher wrote:

so wish I could see these pictures!!! :furious:

check now

arcticbutcher · **Posted:** Tue Mar 27, 2012 1:18 pm

I can't see any pictures on these boards... not sure why

cgass · **Posted:** Tue Mar 27, 2012 1:31 pm

arcticbutcher wrote:

I can't see any pictures on these boards... not sure why

Are you using IE9?

http://www.lostjeeps.com/forum/phpBB3/viewtopic.php?f=37&t=60728

arcticbutcher · **Posted:** Tue Mar 27, 2012 5:47 pm

yes I am using IE9, I'll have to look into this

onegoodpunk · **Posted:** Tue Mar 27, 2012 8:21 pm

the strut fork on yours is way different then on my 08 looks like they beefed it up alot wonder why. Looks good!

norcalarctic · **Posted:** Tue Mar 27, 2012 9:01 pm

arcticbutcher wrote:

I can't see any pictures on these boards... not sure why

Try using Goggle Chrome as your browser,I had the same issue with Internet Explorer.

Looks good Marco, nice job done. You have no issues in the rear with the 2 isos added? So you think after I add my JBA spacer plate to front without clevis and 1 isos to rear should level out or leave off the rear isos for when my HD/MD coil OME lift is done? My shocks are standard OME not the extended length. I did get my JBA gen 5.5 UCAs so I hope my alignment and camber is OK at approximate 2.5" lift in front.

musclezmarinara · **Posted:** Tue Mar 27, 2012 10:24 pm

norcalarctic wrote:

arcticbutcher wrote:

I can't see any pictures on these boards... not sure why

Try using Goggle Chrome as your browser,I had the same issue with Internet Explorer.

Looks good Marco, nice job done. You have no issues in the rear with the 2 isos added? So you think after I add my JBA spacer plate to front without clevis and 1 isos to rear should level out or leave off the rear isos for when my HD/MD coil OME lift is done? My shocks are standard OME not the extended length. I did get my JBA gen 5.5 UCAs so I hope my alignment and camber is OK at approximate 2.5" lift in front.

Small clanking in rear must check that tomorrow on the driver side, other than that drives great
no issues on the isos that should level out well mines almost perfect

Id say closer to a 3" mine is

32s are ordered cant wait to fit those on !

At The Helm · **Posted:** Tue Mar 27, 2012 11:27 pm

Hate break it to you but 285/75/16 is almost 33" tall. You'll likely have multiple issues especially with the spacers.
The lift looks good though! How bad is the a arm contact?

musclezmarinara · **Posted:** Wed Mar 28, 2012 3:14 pm

Spacers on
Before spacer

After

What kind of issues? :/

At The Helm · **Posted:** Wed Mar 28, 2012 6:06 pm

musclezmarinara wrote:

What kind of issues? :/

Fitment. You might get em to fit if you remove your front wheel well liners and flatten the pinch weld completely. Even then i don't know. The rear probably will rip off the flares upon flex unless you bumpstop the crap out it.
It looks like you plan on regearing and hopefully you do lockers while your at it. Beside the obvious reason for lockers they will decrease the chance of exploding your aluminum front diff housing.

norcalarctic · **Posted:** Wed Mar 28, 2012 9:09 pm

Check out E2's profile pics on his signature, those pictures are worth a thousand words on his JBA 4" lift. :shock:

musclezmarinara · **Posted:** Wed Mar 28, 2012 10:55 pm

norcalarctic wrote:

Check out E2's profile pics on his signature, those pictures are worth a thousand words on his JBA 4" lift. :shock:

looks pretty good, im goign to test fit those 285s ..... the 265s look so small and i dislike it. also its the reason my steering rack blew out because the tires were to small and got caught in the rocks.

Not saying im going crazy rock crawling but Id like something capable.

Well see what can be done before i mount them because once mounted they cannot be exchanged.

So well see, probably remove fender liners and have my welder jump in there and do some modification.

The rear fenders are the real concern.

musclezmarinara · **Posted:** Fri Mar 30, 2012 12:31 pm

OH BOY

KK_Canuck_Guy · **Posted:** Fri Mar 30, 2012 1:26 pm

musclezmarinara wrote:

Spacers on
Before spacer

After

Hey what size and brand of spacers did you use?

musclezmarinara · **Posted:** Fri Mar 30, 2012 1:44 pm

KK_Canuck_Guy wrote:

musclezmarinara wrote:

Spacers on
Before spacer

After

Hey what size and brand of spacers did you use?

1.25 Spider Trax

CoopaTroopa · **Posted:** Fri Mar 30, 2012 3:05 pm

musclezmarinara wrote:

OH BOY

when are you throwing them on?

smigelskijk · **Posted:** Fri Mar 30, 2012 3:49 pm

musclezmarinara wrote:

OH BOY

Nice

tommudd · **Posted:** Fri Mar 30, 2012 4:26 pm

get out the chain saw :wink:

** Musclez KK Arctic BUILD THREAD **

Who is online

Musclez KK Arctic BUILD THREAD