It is currently Wed Oct 15, 2025 2:20 pm

View unanswered posts | View active topics


Board index » KJ/KK/KL Liberty/Cherokee Discussion Areas » KK Discussion---2008-2012 Liberty/Cherokee Models

All times are UTC - 5 hours [ DST ]



Post new topic Reply to topic  Page 1 of 1
  [ 8 posts ] 
  Print view Previous topic | Next topic 
Author Message
musclezmarinara
 Post subject: JBA Bump Stop Install Assistance>
PostPosted: Mon Apr 09, 2012 11:11 pm 
Offline
LOST Junkie
User avatar

Joined: Mon Nov 28, 2011 3:59 pm
Posts: 808
Location: NJ
Hey guys

my ome setup is all set and installed

got a set of the JBA Rear Red Bump Stops, but there is no place to mount these guys....any assistance?

_________________
2012 KK Cherokee * Arctic by Musclez * Mineral Gray
- Too Much to list BUILD THREAD
Top
 Profile  
 
At The Helm
 Post subject: Re: JBA Bump Stop Install Assistance>
PostPosted: Mon Apr 09, 2012 11:37 pm 
Offline
Lifetime Member & Advertising Vendor
Lifetime Member & Advertising Vendor
User avatar

Joined: Mon Sep 06, 2010 5:52 pm
Posts: 2172
Location: NEVADA
They go on the lower spring seat. You'll have to remove the rear springs to drill the hole.
Here's a write up from Budke at kjcountry: http://www.jeepkj.com/forum/f202/how-in ... ion-43989/

_________________
2010 KK 4WD BRILLIANT BLACK
Fox/King/Bilstein ATH BUMPERS ATH RACK GY DURATRACS

ATHFAB.com
Top
 Profile  
 
DirtyKK
 Post subject: Re: JBA Bump Stop Install Assistance>
PostPosted: Tue Apr 10, 2012 12:20 am 
Offline
LOST Addict
User avatar

Joined: Thu Oct 29, 2009 5:59 pm
Posts: 2127
Location: Navarre FL
you have to drill a hole in the spring mount. those bump stops were terrible imo. my upper stop would only half way hit the lower stop and wasnt limiting travel enough. i went with zone bump stops and carriage bolts. i used the carriage bolts because regular hex head hardware was tearing up the oem upper stops.
Top
 Profile  
 
musclezmarinara
 Post subject: Re: JBA Bump Stop Install Assistance>
PostPosted: Tue Apr 10, 2012 10:32 am 
Offline
LOST Junkie
User avatar

Joined: Mon Nov 28, 2011 3:59 pm
Posts: 808
Location: NJ
DirtyKK wrote:
you have to drill a hole in the spring mount. those bump stops were terrible imo. my upper stop would only half way hit the lower stop and wasnt limiting travel enough. i went with zone bump stops and carriage bolts. i used the carriage bolts because regular hex head hardware was tearing up the oem upper stops.

Better off with those? or leave stock in?

_________________
2012 KK Cherokee * Arctic by Musclez * Mineral Gray
- Too Much to list BUILD THREAD
Top
 Profile  
 
At The Helm
 Post subject: Re: JBA Bump Stop Install Assistance>
PostPosted: Tue Apr 10, 2012 10:52 am 
Offline
Lifetime Member & Advertising Vendor
Lifetime Member & Advertising Vendor
User avatar

Joined: Mon Sep 06, 2010 5:52 pm
Posts: 2172
Location: NEVADA
musclezmarinara wrote:
DirtyKK wrote:
you have to drill a hole in the spring mount. those bump stops were terrible imo. my upper stop would only half way hit the lower stop and wasnt limiting travel enough. i went with zone bump stops and carriage bolts. i used the carriage bolts because regular hex head hardware was tearing up the oem upper stops.

Better off with those? or leave stock in?

The stock orange colored bump stops stay where they are. Esp with your 32s i would run them.

_________________
2010 KK 4WD BRILLIANT BLACK
Fox/King/Bilstein ATH BUMPERS ATH RACK GY DURATRACS

ATHFAB.com
Top
 Profile  
 
KK_Canuck_Guy
 Post subject: Re: JBA Bump Stop Install Assistance>
PostPosted: Tue Apr 10, 2012 2:24 pm 
Offline
LOST Member
User avatar

Joined: Mon Sep 28, 2009 9:40 pm
Posts: 105
Location: Coquitlam, BC, Canada
musclezmarinara wrote:
Hey guys

my ome setup is all set and installed

got a set of the JBA Rear Red Bump Stops, but there is no place to mount these guys....any assistance?


SOoo...curious...any pics with the 32's?? Looking forward to seeing them :)

_________________
Ian
2008 KK Sport 4x4
OME HD/MD Lift (2.25inches)
Tires : LT 245/75/R16 Goodyear Wrangler DuraTrac's
Speakers: Alpine SC600's component front, Coax rear
Top
 Profile  
 
musclezmarinara
 Post subject: Re: JBA Bump Stop Install Assistance>
PostPosted: Tue Apr 10, 2012 4:26 pm 
Offline
LOST Junkie
User avatar

Joined: Mon Nov 28, 2011 3:59 pm
Posts: 808
Location: NJ
KK_Canuck_Guy wrote:
musclezmarinara wrote:
Hey guys

my ome setup is all set and installed

got a set of the JBA Rear Red Bump Stops, but there is no place to mount these guys....any assistance?


SOoo...curious...any pics with the 32's?? Looking forward to seeing them :)


not yet :/

_________________
2012 KK Cherokee * Arctic by Musclez * Mineral Gray
- Too Much to list BUILD THREAD
Top
 Profile  
 
norcalarctic
 Post subject: Re: JBA Bump Stop Install Assistance>
PostPosted: Thu Apr 12, 2012 8:27 pm 
Offline
LOST Newbie

Joined: Mon Jan 02, 2012 11:30 pm
Posts: 55
Location: The Golden State
Speaking of rear bump stops, any pics or info on hockey pucks that some of you have installed. Getting my OME + 1 top isos. lift finally done next week. Do I need extra bump stops besides the factory ones for this lift in rear? Also, one or two pucks? Only stepping up one size to a 245/75/16 tire. I got Terra Flex bump stops for the front already. Thanks

_________________
12KK ArcticWinterChill 4x4 commandTrac II
OME/JBA 2.0 lift, JBA UCA's, RRO sliders
Mopar skids, tow hooks, & receiver hitch
Top
 Profile  
 
Display posts from previous:  Sort by  
Post new topic Reply to topic  Page 1 of 1
  [ 8 posts ] 

Board index » KJ/KK/KL Liberty/Cherokee Discussion Areas » KK Discussion---2008-2012 Liberty/Cherokee Models

All times are UTC - 5 hours [ DST ]

Who is online

Users browsing this forum: No registered users and 26 guests

You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum

Search for:
Jump to:  
Powered by phpBB © 2000, 2002, 2005, 2007 phpBB Group. Color scheme by ColorizeIt!
Logo by pixeldecals.com

Advertisements by Advertisement Management