L.O.S.T. KJ TRAIL TESTED EDITION BADGES!

pixeldzn · **Posted:** Mon Apr 17, 2006 7:44 pm

I have a couple extra. If they aren't gone after MOAB, one is yours. I am open to ordering more as well, and will start that up after May 1 when I return from my road trip.

mississippimudkj · **Posted:** Mon Apr 17, 2006 10:09 pm

i would like one.. if you have any left, i didnt read the whole six pages but i do want one!

x3rdxStrikex · **Posted:** Mon Apr 17, 2006 10:20 pm

mississippimudkj wrote:

....................... i didnt read the whole six pages but i do want one!

and so it begins again..... :roll:

pixeldzn · **Posted:** Wed Apr 19, 2006 7:07 pm

First Batch SHIPPED

Pleaser post here if you have interest in getting in on the second buy I will start up in early May.

4wdParakeet · **Posted:** Thu Apr 20, 2006 9:40 pm

YESSSSSSSSSSSSSSSSSSSSSSSSSSSSS. Your my new best friend Pixel.

Parakeet

2006KJSPORT4x4 · **Posted:** Thu Apr 20, 2006 10:05 pm

I'm in if you don't have any extras after MOAB.....

benmar2000 · **Posted:** Fri Apr 21, 2006 8:43 pm

Got mine today... It is super nice.. Nice detail.. You can tell it is top quality.. Now to decide where to put it.. Hmmm..

Ben

Nik · **Joined:** Sat Apr 22, 2006 12:56 am **Posts:** 5

I'm in for the second round.

Nik

Guest · **Posted:** Sat Apr 22, 2006 9:27 pm

Badge looks great by itself - so, now how do I get it back off without scratching my paint? Seriously, I'd like to know because it's on like cement right now.

Where I wanted to mount it, below my CRD badge on the rear tail gate, would not work because the sheet metal is so curved on the rear tail gate that the long and thick aluminum badge will not bend to lay falt enough to attach. So, I went below the "trail rated" circle from Jeep. The badge is installed level, but the hood curves down from back to front, as does almost every other line on the jeep, so now it looks way crooked - even though it's level. Also, a circle next to a rectangle does not look good(nothing like being tired when doing a project as hind sight is always 20/20).

Anyone with some auto detailing tips to get this off? Also, can I get more of this heavy duty adhesive so I can re-try later in a different location?

4wdParakeet · **Posted:** Sat Apr 22, 2006 9:28 pm

GOT IT!!!!!!!!! Very nice pixel very nice. I'm putting mine on the fridge so it doesn't get icky and dirty :twisted:

. No actually I've peeled the 3.7L from above the Renegade badge and it's going to live there. The real question is should I paint it.....

Parakeet

pixeldzn · **Posted:** Sat Apr 22, 2006 9:49 pm

To remove it, heat it up a bit with a hair dryer and then run some fishing line or dental floss behind it.

Guest · **Posted:** Sat Apr 22, 2006 9:55 pm

pixeldzn wrote:

To remove it, heat it up a bit with a hair dryer and then run some fishing line or dental floss behind it.

Now THATS a sweet trick! Thanks! Then I can try it somewhere else with new adhesive. Time for beer... Here's some blurry pics. The badge itself is AWESOME, I just want to move mine...

Maybe.... I'll just pop off the Jeep trail rated badge.... hmmmmmm

pixeldzn · **Posted:** Sat Apr 22, 2006 10:02 pm

Here's where I put mine. Curvature wasn't a problem here.

Not the best pic, but it's all I've got at the moment.

0311_DoC · **Posted:** Sat Apr 22, 2006 10:41 pm

alljeep wrote:

Badge looks great by itself - so, now how do I get it back off without scratching my paint? Seriously, I'd like to know because it's on like cement right now.

Where I wanted to mount it, below my CRD badge on the rear tail gate, would not work because the sheet metal is so curved on the rear tail gate that the long and thick aluminum badge will not bend to lay falt enough to attach. So, I went below the "trail rated" circle from Jeep. The badge is installed level, but the hood curves down from back to front, as does almost every other line on the jeep, so now it looks way crooked - even though it's level. Also, a circle next to a rectangle does not look good(nothing like being tired when doing a project as hind sight is always 20/20).

Anyone with some auto detailing tips to get this off? Also, can I get more of this heavy duty adhesive so I can re-try later in a different location?

basically what you have to do is get some fishing line and use a sawing motion to get it off. you can also go to www.billetbadges.com for more in depth instrucions. and then go get some more adhesive at the auto parts store. HTH.

Renegade363 · **Posted:** Sun Apr 23, 2006 2:16 pm

I'm in for the second round.
they look nice

rocketjocky · **Posted:** Mon Apr 24, 2006 8:19 pm

Hey Pixeldzn, I've been busy w/a new job... is it too late for me to get one? If not I'll send paypal ASAP.

Thanks

pixeldzn · **Posted:** Tue Apr 25, 2006 8:22 pm

Again, I'll be doing another group buy after Moab is over.

MoladoGuy · **Posted:** Tue Apr 25, 2006 9:11 pm

Put me down for Round #2 of Badge Ordering! They look great!

OutbackSurvivor · **Posted:** Wed Apr 26, 2006 10:24 pm

Hi Pixeldzn, can I order one as well but I am from Australia?

pixeldzn · **Posted:** Tue May 02, 2006 9:31 am

OK. Locking this thread, destickyfying, and beginning a new one for the second group buy.

L.O.S.T. KJ TRAIL TESTED EDITION BADGES!

Who is online