Is Indiana dead

BugginKJ · **Joined:** Mon Jul 06, 2009 7:35 pm **Posts:** 4576

Bolts and they can be obtained from the hardware store. :ROTFL:

Nut zerks , ask Larry, he might have some.

BugginKJ · **Joined:** Mon Jul 06, 2009 7:35 pm **Posts:** 4576

PermanentGrin wrote:

tommudd wrote:

What exact codes are you finding
or whats it doing exactly ?
Not charging, or ???
Sometimes although its a PITA you have to pay the piper to not have to spend a bunch "trying" to find the issue

I don't recall the codes, but they were C codes that indicated "high or low voltage to the ECU" or something along those lines. Sometimes the internal backlights will go out here or there. Last night it was part of the shift console out. No battery charging issues.

They found some jacked up wiring under the dash, and fixed that, and same story: ran fine for a day, then same intermittent problem. I looked under the hood at the fuel filter bracket, and I can't tell where it would rub exactly, as everything is wrapped in fabric tape whatever. One day it will run fine. The next, the ETCL will come on, and after some time, it will just lose power and then come back up to speed. On the way to work this morning, I had the cruise on 62 MPH, and it started to act up, but only lost 2-3 MPH, hung there, and eventually went back to 62 MPH. Seldom outright dies, just goes to idle RPM. In fact, hasn't died since last repair 9 or so months ago. Sometimes, I even get a full up CEL/MIL light to come on, but it always goes away. Really been acting up in the cold.

viewtopic.php?f=5&t=45800&p=759112#p759112

Wow this is a lil much for me to wrap my one brain cell around right at this moment but if I had to guess with a knee jerk reaction, I would say ya have a wiring issue that still needs resolved.

MoD · **Joined:** Sat Mar 17, 2012 12:53 am **Posts:** 1343

BugginKJ wrote:

Bolts and they can be obtained from the hardware store. :ROTFL:

Nut zerks , ask Larry, he might have some.

im hoping mudd might have some he could part with. i see the nuts are m10x1.5x30 but i dont know what that means. i assume metric 10

BugginKJ · **Joined:** Mon Jul 06, 2009 7:35 pm **Posts:** 4576

10mm bolt with a 1.5 pitch and 30 mm long and they need to be hardened

tommudd · **Posted:** Sat Jan 26, 2013 11:19 pm

One or two nut zerts, everything else you can bolt on by drilling through the cross member
No need for a lot of hoopla or fancy tools
drill , bolts/nuts washers, wrenches done

MoD · **Joined:** Sat Mar 17, 2012 12:53 am **Posts:** 1343

nice...now to get a few nutzerts...and sand paper and to spraypaint

501 · **Posted:** Sun Jan 27, 2013 2:05 am

Check True value hardware, that's where I picked some nutzerts up at when I needed some.

MoD · **Joined:** Sat Mar 17, 2012 12:53 am **Posts:** 1343

Thanks 501! Now to find a true value...or check lowes

John3:17 · **Posted:** Sun Jan 27, 2013 9:35 am

MoD wrote:

Thanks 501! Now to find a true value...or check lowes

Lowes in MD didnt have them, didnt check True Value. Bought mine at a place called automotive fastners. Bought a standard size in Grade 8 instead of metric, paid $3 for 20 of them.

tommudd · **Posted:** Sun Jan 27, 2013 12:04 pm

MoD wrote:

nice...now to get a few nutzerts...and sand paper and to spraypaint

need two for the transfer case where it mounts to the frame, other wise you can drill and bolt everything else on, then you don't have to worry about them cheap nut zerts coming loose
Of course that is mainly from folks not knowing how to use them properly but still......................................

MoD · **Joined:** Sat Mar 17, 2012 12:53 am **Posts:** 1343

tommudd wrote:

MoD wrote:

nice...now to get a few nutzerts...and sand paper and to spraypaint

need two for the transfer case where it mounts to the frame, other wise you can drill and bolt everything else on, then you don't have to worry about them cheap nut zerts coming loose
Of course that is mainly from folks not knowing how to use them properly but still......................................

^^^^ like me... and i do like the standard grade 8 idea...andi thought the gas tank one had to use them. Its awesome i only need 2 and 20 for $3 seems super reasonable

tommudd · **Posted:** Sun Jan 27, 2013 12:35 pm

gas tank skid takes the same bolts as the hitch If you have the hitch you're good to go

John3:17 · **Posted:** Sun Jan 27, 2013 2:04 pm

MoD wrote:

tommudd wrote:

MoD wrote:

nice...now to get a few nutzerts...and sand paper and to spraypaint

need two for the transfer case where it mounts to the frame, other wise you can drill and bolt everything else on, then you don't have to worry about them cheap nut zerts coming loose
Of course that is mainly from folks not knowing how to use them properly but still......................................

^^^^ like me... and i do like the standard grade 8 idea...andi thought the gas tank one had to use them. Its awesome i only need 2 and 20 for $3 seems super reasonable

I think they were 13 cents each, other places were $1 each and up. http://www.automotivefasteners.com/
This is where I got them as they are a local buisness here.

MoD · **Joined:** Sat Mar 17, 2012 12:53 am **Posts:** 1343

tommudd wrote:

gas tank skid takes the same bolts as the hitch If you have the hitch you're good to go

No no hitch

John ill have to look into that!

John3:17 · **Posted:** Sun Jan 27, 2013 2:08 pm

MoD wrote:

tommudd wrote:

gas tank skid takes the same bolts as the hitch If you have the hitch you're good to go

No no hitch

John ill have to look into that!

Mine didnt have the skid or hitch but the nuts were in place at the gas tank, I just had to clean them good as the threads were rusted.

MoD · **Joined:** Sat Mar 17, 2012 12:53 am **Posts:** 1343

i cant find them on the site...i will see what i can find elsewhere

John3:17 · **Posted:** Sun Jan 27, 2013 9:34 pm

If ya cant find them give them a call, i know they have them there.

MoD · **Joined:** Sat Mar 17, 2012 12:53 am **Posts:** 1343

alright i will probably call them tomorrow. I think i am going to put them on asap and then when it gets warm take them off and paint them because in this temp i know painting them is a waste

John3:17 · **Posted:** Mon Jan 28, 2013 7:26 pm

Hey Moe Dddddddd, its awful quiet in Indiana!

:ALONE:

MoD · **Joined:** Sat Mar 17, 2012 12:53 am **Posts:** 1343

I know. No one likes me

thinking about organizing a meet and greet though...

Is Indiana dead

Who is online