It is currently Tue Sep 30, 2025 12:56 am

All times are UTC - 5 hours [ DST ]




Post new topic Reply to topic  [ 12 posts ] 
Author Message
 Post subject: Fuel line piece... help locating it
PostPosted: Sun Jan 10, 2016 2:42 pm 
Offline
LOST Newbie

Joined: Tue Oct 07, 2014 10:33 pm
Posts: 96
Location: South Carolina
While putting in the Sasquatch kit, we broke a plastic piece that is part of the diesel fuel supply.

This piece attached to the block, passenger (strike, mean driver) side, with one bolt and the injection fuel line from the rear most injector comes into it from the top. Two larger fuel lines, one to the back and one to the fuel head (I believe) also come out of it from the sides.

The nipple that attaches to the fuel injection line broke off. The part itself carries a Dayco indicator and part number PA66GF30. I have found one reference for this number which indicates it is a polymer matrix composite, so may not be a part number, but a manufacturers number indicating composition or materials in the part.

OK, looks like its called a "fuel return line bridge" and for a piece of plastic, it is expensive. Part number we have found...5142809AB Mopar.

Does anyone have an idea what the part might be called and even better, where it can be found?

Thank you!


Last edited by vertrx7 on Sun Jan 10, 2016 3:16 pm, edited 1 time in total.

Top
 Profile  
 
 Post subject: Re: Fuel line piece... help locating it
PostPosted: Sun Jan 10, 2016 3:01 pm 
Offline
LOST Newbie

Joined: Tue Oct 07, 2014 10:33 pm
Posts: 96
Location: South Carolina
OK, presuming it can be found at the dealer...is there anything/process I need to perform to install and get the vehicle running? I ask because the fuel system has now been opened. I'm thinking air in the line and all that...

Thank you!


Top
 Profile  
 
 Post subject: Re: Fuel line piece... help locating it
PostPosted: Sun Jan 10, 2016 3:11 pm 
Offline
LOST Junkie

Joined: Sun May 01, 2011 2:27 pm
Posts: 834
Location: Milford, IL
Did you mean on the driver side? There is no fuel related stuff on the passenger side. Sounds like you broke the return bridge thing. There is a thread on here where a few have made their own out of brass fittings. Hopefully someone can link it. It's definitely a better/cheaper option than buying that expensive part

_________________
2005 Crd Silver Limited- arps, rockers, 7v etechno's, egr deleted, v6 airbox, metal cac's. Yeti's stage 2 tune. Euro TC, Ram tcm, pml transmission pan, facet lift pump


Top
 Profile  
 
 Post subject: Re: Fuel line piece... help locating it
PostPosted: Sun Jan 10, 2016 3:15 pm 
Offline
LOST Newbie

Joined: Tue Oct 07, 2014 10:33 pm
Posts: 96
Location: South Carolina
Yes Sir, you are correct, driver side. I will edit and make the change. Not sure about the brass thing because that means messing with the hoses and I'm not so sure I want to get into all of that.

The piece is expensive, no doubt!


Top
 Profile  
 
 Post subject: Re: Fuel line piece... help locating it
PostPosted: Sun Jan 10, 2016 3:20 pm 
Offline
Lifetime Member
Lifetime Member

Joined: Sun Mar 28, 2010 9:15 am
Posts: 5431
Location: Tallahassee, Florida
Not where I can post a link but just do a Google search for lost kj fuel return block. What you need should be at the first search hit.

_________________
Sold to LOST member my 05 Ltd, GDE Stg II turbo + TCM tune, SunCoast TC w. Transgo kit, Steiger window regulators, Samcos, Fumoto valve, 2nd gen filter head with Lub. Spec. bleeder, Hayden clutch & 11 blade fan, inverted spare, P-1 battery, BF Goodrich Long Trail TAs, Etecno1 glow plugs, timing belt at 50K miles/8 yrs


Top
 Profile  
 
 Post subject: Re: Fuel line piece... help locating it
PostPosted: Sun Jan 10, 2016 3:23 pm 
Offline
LOST Junkie

Joined: Sun May 01, 2011 2:27 pm
Posts: 834
Location: Milford, IL
vertrx7 wrote:
Yes Sir, you are correct, driver side. I will edit and make the change. Not sure about the brass thing because that means messing with the hoses and I'm not so sure I want to get into all of that.

The piece is expensive, no doubt!



Your gonna have to mess with them anyway putting a new piece on so why not make it more durable and not break if you look at it funny

_________________
2005 Crd Silver Limited- arps, rockers, 7v etechno's, egr deleted, v6 airbox, metal cac's. Yeti's stage 2 tune. Euro TC, Ram tcm, pml transmission pan, facet lift pump


Top
 Profile  
 
 Post subject: Re: Fuel line piece... help locating it
PostPosted: Sun Jan 10, 2016 3:42 pm 
Offline
LOST Newbie

Joined: Tue Oct 07, 2014 10:33 pm
Posts: 96
Location: South Carolina
Then two questions if I go the repair route:

1. How were the brass fittings attached to the block since one would not want it hanging, stressing the lines I presume.

2. In the pictures, especially on the IDparts site, there is a white plastic piece sitting on the end of the rubber hose. Based on what I've read, when doing the repair, that valve along with the hose is replaced by the marine fuel hose. That valve or white piece does not serve a purpose?

Thank you for the references to the brass repair pieces. I'm working myself up to doing the repair as I get closer to understanding the process.


Top
 Profile  
 
 Post subject: Re: Fuel line piece... help locating it
PostPosted: Sun Jan 10, 2016 10:03 pm 
Offline
LOST Member

Joined: Sat Apr 25, 2015 3:26 pm
Posts: 186
Location: Dallas, TX
Some of us have JB welded the pieces left. It is just a junction for return fuel etc and is low pressure line. So brass would be way more than what you need.

_________________
'06 Liberty CRD Limited. Bought at 91K miles.
ARP studs, New rockers, Stant inline tstat, Weeks 1&2, Provent, IDParts Silicone hoses,
2-1/2" Full OME lift, Timing belt, Water pump, TransGo kit, Plastic fan, Fumoto
2nd gen fuel head with 2nd stage 2 micron filter, in-tank lift pump, G2 Rear Diff Cover


Top
 Profile  
 
 Post subject: Re: Fuel line piece... help locating it
PostPosted: Mon Jan 11, 2016 10:54 pm 
Offline
LOST Newbie

Joined: Tue Oct 07, 2014 10:33 pm
Posts: 96
Location: South Carolina
Thank you. I found a pretty good little air hose with brass junction barb description on here. Essentially similar to the plumbing supply pieces. For some reason, it "speaks" to me. :)

Honestly, I do feel dumb though with the posts I have now found on this very topic. Seems most people are confused by the part and what its called when they encounter our very situation. Amazing how similar the topics are.

The post I'm referencing is here with the air hose junction:

viewtopic.php?f=5&t=82155


Top
 Profile  
 
 Post subject: Re: Fuel line piece... help locating it
PostPosted: Mon Jan 11, 2016 11:10 pm 
Offline
LOST Junkie

Joined: Sun May 01, 2011 2:27 pm
Posts: 834
Location: Milford, IL
Don't feel dumb. Your just newer than some of us. I just wished I could have linked it sooner for ya.

_________________
2005 Crd Silver Limited- arps, rockers, 7v etechno's, egr deleted, v6 airbox, metal cac's. Yeti's stage 2 tune. Euro TC, Ram tcm, pml transmission pan, facet lift pump


Top
 Profile  
 
 Post subject: Re: Fuel line piece... help locating it
PostPosted: Fri Jan 15, 2016 9:56 pm 
Offline
LOST Newbie

Joined: Fri Dec 10, 2010 1:18 pm
Posts: 17
Don't feel dumb, honest question. Here's your help. Go to the Home depot plumbing dept. where the brass fittings are Get the right size of barbed nipples and two "T"'s of the 1/4" size. nipples also 1/4 on the threads and 1 short connecting nipple assemble these pieces in the same configuration as the FUEL MANIFOLD. Get Diesel grade fuel hose it has a liner inside to prevent degradation of the hose from the fuel. Its costly but important.
Do a search on here and look for the Fuel return Manifold and the brass set up should come up some where.
This same thing happen to us and this repair is supper. Should have been done from VM.
Good luck.


Top
 Profile  
 
 Post subject: Re: Fuel line piece... help locating it
PostPosted: Tue Jan 19, 2016 10:45 pm 
Offline
LOST Newbie

Joined: Tue Oct 07, 2014 10:33 pm
Posts: 96
Location: South Carolina
Substantially followed that advice, but bought the octagonal air regulator piece. Went to plumbing section to pick up the small barbs. Waited on the regulator piece to come in. Came in today. Bought the Mopar piece in the meantime as the kid has to have the car completed to go back to college. We got it together tonight, in for alignment.


Top
 Profile  
 
Display posts from previous:  Sort by  
Post new topic Reply to topic  [ 12 posts ] 

All times are UTC - 5 hours [ DST ]


Who is online

Users browsing this forum: No registered users and 169 guests


You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum

Search for:
Jump to:  
Powered by phpBB © 2000, 2002, 2005, 2007 phpBB Group. Color scheme by ColorizeIt!
Logo by pixeldecals.com