KJ Tri-Angulated Bolt On 4 Link from JBA

Gyro · **Posted:** Tue Oct 20, 2015 7:22 pm

Lancer wrote:

I still can't find it on the website!

It's in the rear shocks & coil springs section http://jeepinbyal.com/liberty-2002-2007 ... rings.html

Gyro

Lancer · **Posted:** Wed Oct 21, 2015 1:04 am

Thanks!

CRD_Joe · **Posted:** Tue Nov 03, 2015 6:39 am

Will this be offered as part of his lift packages anytime soon? Should I hold off getting the 4" until this has been released?

tommudd · **Posted:** Tue Nov 03, 2015 1:00 pm

Good question
I'll find out
or you can just send Marlin a message as well

Pippobug · **Posted:** Fri Nov 06, 2015 10:42 am

Quick question, I have the the Y link extension from JBA and since installing it my rear prop shaft knocks against the exhaust when I go with full extension, if I bought this i wouldn't need Y Link anymore and would the Tri Angulated set up stop the knocking against the exhaust at full articulation? Also is it that it would improve the rear U Joints life on the prop shaft as I can rotate the angle on the axle to be less acute and more in line?

Fil.

JeepMorrison · **Joined:** Thu Jul 16, 2009 11:34 am **Posts:** 1236

Pippobug wrote:

Quick question, I have the the Y link extension from JBA and since installing it my rear prop shaft knocks against the exhaust when I go with full extension, if I bought this i wouldn't need Y Link anymore and would the Tri Angulated set up stop the knocking against the exhaust at full articulation? Also is it that it would improve the rear U Joints life on the prop shaft as I can rotate the angle on the axle to be less acute and more in line?

Fil.

#1 I cant answer becuase I dont have one or that issue

#2 Yes for sure

Sent from my SM-N900P using Tapatalk

Lancer · **Posted:** Sat Nov 07, 2015 5:51 am

Pippobug wrote:

Quick question, I have the the Y link extension from JBA and since installing it my rear prop shaft knocks against the exhaust when I go with full extension, if I bought this i wouldn't need Y Link anymore and would the Tri Angulated set up stop the knocking against the exhaust at full articulation? Also is it that it would improve the rear U Joints life on the prop shaft as I can rotate the angle on the axle to be less acute and more in line?

Fil.

You going for it Fil? I'm thinking of it

Adrian

Pippobug · **Posted:** Sat Nov 07, 2015 4:13 pm

Adrian
Not sure yet as it's a bit pricey when you add shipping & Duty at this end, but the idea is very good. Just need to know if it stops the knocking against the exhaust.
Fil

tommudd · **Posted:** Sun Nov 08, 2015 5:46 pm

Pippobug wrote:

Adrian
Not sure yet as it's a bit pricey when you add shipping & Duty at this end, but the idea is very good. Just need to know if it stops the knocking against the exhaust.
Fil

Where is yours hitting at?
Mine still has stock tail pipe on it and doesn't touch, I could take some photos to show if needed
Let me know

Pippobug · **Posted:** Tue Mar 22, 2016 9:22 am

Tom,

I will try to get some pictures now the weather is improving to show you where it's knocking against the exhaust.

Also any up dates from people how have fitted the 4 Link? I would like some feed back as I am considering buying one and the cost shipped over to the UK comes to over $600 (excluding taxes at this end, another 20%), you can buy a lot of replacement A arms for that money.....

Fil.

Mountainman · **Posted:** Tue Mar 22, 2016 12:06 pm

I would just have a muffler shop bend the pipe to slide the muffler over an inch or so. Shouldn't be very expensive. About $100 here

Pippobug · **Posted:** Wed May 18, 2016 2:41 am

tommudd wrote:

Pippobug wrote:

Adrian
Not sure yet as it's a bit pricey when you add shipping & Duty at this end, but the idea is very good. Just need to know if it stops the knocking against the exhaust.
Fil

Where is yours hitting at?
Mine still has stock tail pipe on it and doesn't touch, I could take some photos to show if needed
Let me know

Tom,

Apologies for the long delay in getting back to you with a photo of where the rear prop shaft is knocking against the exhaust box, here is the photo, sadly not the best but should give you an idea:

Any Idea how to make it stop? I am sitting at 22 in at the back (and on all corners) I have already 3 1/2 hockey pucks at the back so around 3.5" bump stop.

Fil.

G.O.A.T. · **Joined:** Wed Jan 27, 2016 1:11 am **Posts:** 149

Pippobug wrote:

tommudd wrote:

Pippobug wrote:

Adrian
Not sure yet as it's a bit pricey when you add shipping & Duty at this end, but the idea is very good. Just need to know if it stops the knocking against the exhaust.
Fil

Where is yours hitting at?
Mine still has stock tail pipe on it and doesn't touch, I could take some photos to show if needed
Let me know

Tom,

Apologies for the long delay in getting back to you with a photo of where the rear prop shaft is knocking against the exhaust box, here is the photo, sadly not the best but should give you an idea:

Any Idea how to make it stop? I am sitting at 22 in at the back (and on all corners) I have already 3 1/2 hockey pucks at the back so around 3.5" bump stop.

Fil.

Looks like the fix will be either a smaller muffler or a BFH

Sent from my SM-N900P using Tapatalk

Mountainman · **Posted:** Wed May 18, 2016 8:40 pm

If you can get away without a muffler, you should delete that waste of space. I don't like noise, and I hear zero difference from the magnaflow muffler that my Jeep came with to the now strait pipe that replaced it. The cat silences it well

Mountainman · **Posted:** Wed May 18, 2016 8:55 pm

Is the chromoly upgrade necessary/useful if your not doing extreme/Moab grade wheeling?

G.O.A.T. · **Joined:** Wed Jan 27, 2016 1:11 am **Posts:** 149

Mountainman wrote:

Is the chromoly upgrade necessary/useful if your not doing extreme/Moab grade wheeling?

Id go chromoly on any joint. But those heims arnt the best in the world, so definitely chromoly

Sent from my SM-N900P using Tapatalk

Pippobug · **Posted:** Thu May 19, 2016 8:04 am

G.O.A.T. wrote:

Looks like the fix will be either a smaller muffler or a BFH

Sorry but what do you mean by BFH?

Not changing the muffler and didn't have this problem before I fitted the Y link extension.

flash7210 · **Posted:** Thu May 19, 2016 8:17 am

Pippobug wrote:

G.O.A.T. wrote:

Looks like the fix will be either a smaller muffler or a BFH

Sorry but what do you mean by BFH?

Not changing the muffler and didn't have this problem before I fitted the Y link extension.

Big
eFFing
Hammer

Pippobug · **Posted:** Thu May 19, 2016 8:25 am

flash7210 wrote:

Pippobug wrote:

G.O.A.T. wrote:

Looks like the fix will be either a smaller muffler or a BFH

Sorry but what do you mean by BFH?

Not changing the muffler and didn't have this problem before I fitted the Y link extension.

Big
eFFing
Hammer

Thank you, but that is not the solution, also it's in a hard spot of the exhaust.

Mountainman · **Posted:** Thu May 19, 2016 11:20 am

In that case, like someone said before, just have an exhaust shop bend the pipe a little. I need to do the same thing as my cat is touching the body after my muffler delete.

KJ Tri-Angulated Bolt On 4 Link from JBA

Who is online