SUPER 44

riptricket · **Posted:** Thu May 07, 2009 3:15 pm

auto zone dude told me that i needed to purchase the 18" exhaust pipe with dual flanges (at both ends) so I did! I will be putting this sucker on saturday.

So does the dual flange work or do I need to go back and get the single?

JMSMN · **Posted:** Thu May 07, 2009 6:42 pm

You only need the 18" pipe with the single flange. Both inlet and out let on the super 44 are slightly bigger and 2 1/2" exhaust. You only need the single flared end.

Robbrez · **Posted:** Fri May 08, 2009 1:15 pm

so what i will need is the muffler, 18 inch piece with one flared end and some clamps?
i am not going to use the intermediete pipe i will just be cutting off the stock muffler and leaving it there
if there is anything else let me know as i am going to go and get it today

Logan · **Posted:** Fri May 08, 2009 3:02 pm

riptricket wrote:

12 hours have passed, and noone?

my super 44 is now just the silver color you see now, after 6 months of use. i believe the coating has no effect on the performance of the muffler.

JMSMN · **Posted:** Fri May 08, 2009 6:04 pm

Robbrez wrote:

so what i will need is the muffler, 18 inch piece with one flared end and some clamps?
i am not going to use the intermediete pipe i will just be cutting off the stock muffler and leaving it there
if there is anything else let me know as i am going to go and get it today

That should be it, and a hack saw or a recepricating saw. Just cut off the two inch pipe at both ends of the muffler. Try not to take off too much of the 2 1/2" pipe. Pretty straight forward.

greenrider · **Posted:** Sat May 09, 2009 6:55 am

TO BAD YOU DON'T HAVE SOUND CLIPS OF sTOCK AND THEN WITH THE FLOW

Robbrez · **Posted:** Sat May 09, 2009 9:34 am

greenrider wrote:

TO BAD YOU DON'T HAVE SOUND CLIPS OF sTOCK AND THEN WITH THE FLOW

there are plenty

Cali KJ · **Posted:** Sat May 09, 2009 2:48 pm

Ok on the super 44. Is it a center inlet and a off set out? Or a off set in and out? Is there a difference? The reason i ask is i had mine installed yesterday and told them i wanted.... Center in/ off set out. Just noticed it's offset in and so on. sensored word!!!! Is there any real difference? Sounds great! Some people just can't listen i guess. Was closing time for Richards performance muffler and of course there closed today

Should i go and %$tch about this or let it go? Thanks in advance!!!

riptricket · **Posted:** Sat May 09, 2009 7:08 pm

Does anything hold the new muffler up? or does it just hang?

riptricket · **Posted:** Sat May 09, 2009 7:34 pm

need to do this tonight!!! and I need to know! MORE OF YOU ARE ON OUT THERE!

Can't you tell i'm having fun.... :?:

Dave08 · **Joined:** Fri Nov 02, 2007 4:17 pm **Posts:** 250

it hangs in same as stock set up location.. about

riptricket · **Posted:** Sat May 09, 2009 7:43 pm

there is no hanger though?
b/c I don't want it to rattle around...

riptricket · **Posted:** Sat May 09, 2009 8:53 pm

guess I have to wait until another day... :cry:

I think I have it figured out though...

Ms5490renegade · **Posted:** Sun May 10, 2009 1:27 am

have you seen the new stainless steel series? my black 44 has turned slightly rusty

JMSMN · **Posted:** Sun May 10, 2009 2:28 pm

Right behind the muffler there is a hanger on the pipe. The muffler just hangs on the pipe and it dosent rattle at all. Ther 44 is conciderably smaller than the stock muffler and that one just hangs on the pipe also.

JMSMN · **Posted:** Sun May 10, 2009 2:34 pm

Cali KJ wrote:

Ok on the super 44. Is it a center inlet and a off set out? Or a off set in and out? Is there a difference? The reason i ask is i had mine installed yesterday and told them i wanted.... Center in/ off set out. Just noticed it's offset in and so on. jerks!!!! Is there any real difference? Sounds great! Some people just can't listen i guess. Was closing time for Richards performance muffler and of course there closed today

Should i go and %$tch about this or let it go? Thanks in advance!!!

Did they put it on backwards? :lol:

Cali KJ · **Posted:** Sun May 10, 2009 3:14 pm

JMSMN wrote:

Cali KJ wrote:

Ok on the super 44. Is it a center inlet and a off set out? Or a off set in and out? Is there a difference? The reason i ask is i had mine installed yesterday and told them i wanted.... Center in/ off set out. Just noticed it's offset in and so on. jerks!!!! Is there any real difference? Sounds great! Some people just can't listen i guess. Was closing time for Richards performance muffler and of course there closed today

Should i go and %$tch about this or let it go? Thanks in advance!!!

Did they put it on backwards? :lol:

No. Ive done a few searches and i just seems they used a center inlet and off set out. But mine is off set in and off set out. Guess it's just preference on how it lines up. Like i said though. Crappy install :evil:

. I'm calling the owner tomorrow just so he can see what kinda crap his guys are sending out of his shop. Frustrating cause he's a 4x4 enthusiast himself, Baja 1000 sponsor and driver. So when it comes to exhaust... He knows his stuff. That's all his business does.

He'll make it right though.

Robbrez · **Posted:** Mon May 11, 2009 5:27 pm

so i will be ordering mine tmrw...I just need a confirmation on the pipe while im waiting to get my muffler..
are we sure that it is a 18 inch pipe to fill the gap? i just want to be sure before i buy

JMSMN · **Posted:** Mon May 11, 2009 6:11 pm

Yes in is an 18" pipe flared on one end, am sure because I just installed mine. Keep in mind mine is a 06', dont know if there are any differences on the model years, but 05'-07' sould be the same.

Robbrez · **Posted:** Mon May 11, 2009 6:37 pm

i have an 03' but it should be the same...thank you

SUPER 44

Who is online