How to disable the sealt belt dinger and auto locks??

Fishin' Dave · **Joined:** Sat Aug 12, 2006 3:19 pm **Posts:** 18

Two things on my '05 that really bug me are the seat belt dinger and the auto locks. When I'm on my property doing stuff, I don't want the dinger beeping at me. I've found ways to cheat it, but I want it gone! Also, how can I stop the auto locks? Nothing is worse than geting back there and having the door locked. Please let me know!

Neal · **Posted:** Wed Sep 13, 2006 12:51 am

I snagged these instructions off another forum, but here you go.

The following steps must occur within the first 60 seconds of the ignition switch being turned to the ON or START position.

1. Turn the ignition switch to the OFF position, and buckle the driver's seat belt.

2. Turn the ignition key to the ACCESSORY / RUN position (engine does not need to be running), and wait for the Seat Belt Warning Light to turn off.

3. Within 60 seconds, unbuckle and then re-buckle the driver's seat belt 3 times within 10 seconds, ending with the seat belt buckled.

4. Turn the ignition key to the OFF position. A single chime will sound to signify that you have successfully completed the programming.

Fishin' Dave · **Joined:** Sat Aug 12, 2006 3:19 pm **Posts:** 18

so that will disable it forever? Or just for that trip?

Neal · **Posted:** Wed Sep 13, 2006 11:03 am

Forever, you can toggle it back by repeating the same procedure.

moose · **Posted:** Wed Sep 13, 2006 11:05 am

Fishin' Dave wrote:

so that will disable it forever? Or just for that trip?

Forever. Check in your manual, you will find the instructions there.

ShoreRenegade · **Posted:** Wed Sep 13, 2006 11:05 am

Any idea on the auto lock? That thing annoys the hell out of me. Thanks.

Cacher123 · **Posted:** Wed Sep 13, 2006 1:19 pm

Will that disable the little dashboard light also?

Cowcatcher · **Posted:** Wed Sep 13, 2006 1:26 pm

Cacher123 wrote:

Will that disable the little dashboard light also?

No but the light only stays on for about 5 minutes or less. It is also easier to IGNOR!

Cowcatcher · **Posted:** Wed Sep 13, 2006 1:33 pm

ShoreRenegade wrote:

Any idea on the auto lock? That thing annoys the hell out of me. Thanks.

The auo lock can be done on the EVIC if you have an '05>'06. I think it is a BCM program otherwise.

gone_jeepin · **Posted:** Wed Sep 13, 2006 3:55 pm

what year did the "seat belt dinger" start in the liberty

GilaMonster · **Posted:** Wed Sep 13, 2006 4:45 pm

Neal wrote:

I snagged these instructions off another forum, but here you go.

The following steps must occur within the first 60 seconds of the ignition switch being turned to the ON or START position.

1. Turn the ignition switch to the OFF position, and buckle the driver's seat belt.

2. Turn the ignition key to the ACCESSORY / RUN position (engine does not need to be running), and wait for the Seat Belt Warning Light to turn off.

3. Within 60 seconds, unbuckle and then re-buckle the driver's seat belt 3 times within 10 seconds, ending with the seat belt buckled.

4. Turn the ignition key to the OFF position. A single chime will sound to signify that you have successfully completed the programming.

Thank you very much Neal. Worked on my 2006 CRD.

mlr · **Posted:** Wed Sep 13, 2006 4:51 pm

gone_jeepin wrote:

what year did the "seat belt dinger" start in the liberty

Not sure, but mine is an early 02 and has it.

gone_jeepin · **Posted:** Wed Sep 13, 2006 8:36 pm

cause mine is an 03 and doesn't

moose · **Posted:** Wed Sep 13, 2006 9:00 pm

gone_jeepin wrote:

cause mine is an 03 and doesn't

may just be set to "off". try the proceedure and see if you can turn it on...

Fishin' Dave · **Joined:** Sat Aug 12, 2006 3:19 pm **Posts:** 18

Cowcatcher, what is the EVIC? How do I get rid of the auto locks with EVIC?

Myke · **Posted:** Wed Sep 13, 2006 11:41 pm

My 02 limited never did it.

JQLiberty · **Posted:** Thu Sep 14, 2006 6:24 am

My 04 does and I sure am glad I seen this post. I'll have to try it tonight.

Cowcatcher · **Posted:** Thu Sep 14, 2006 4:44 pm

Fishin' Dave wrote:

Cowcatcher, what is the EVIC? How do I get rid of the auto locks with EVIC?

The EVIC is a display on the ceiling in the middle above the mirror that displays temperature, tire pressure, miles to refuel and other vehicle status messages. It also allows you to program some features like how long the headlights stay on after you shut the rig down or the auto door lock.

Kugellager · **Posted:** Thu Sep 14, 2006 7:26 pm

My 05' sport does not either....but no evic etc.

John
];')

MattyMac1 · **Posted:** Thu Sep 14, 2006 7:36 pm

Fishin' Dave wrote:

Cowcatcher, what is the EVIC? How do I get rid of the auto locks with EVIC?

It's the on-board computer that is overhead by your sunroof. It usually has the compass and temp showing by default. Not all Libby's come with it. If you do have it, you have to cycle through the step button until you reach the auto locks and then can toggle it to have them lock at different speeds or shut it off completely. hope that helps..

How to disable the sealt belt dinger and auto locks??

Who is online