It is currently Thu Oct 22, 2026 4:43 pm

All times are UTC - 5 hours [ DST ]




Post new topic Reply to topic  [ 4 posts ] 
Author Message
 Post subject: Driver's side seat track...
PostPosted: Mon Jul 09, 2007 2:10 pm 
Offline
Lifetime Member
Lifetime Member
User avatar

Joined: Mon Aug 14, 2006 9:57 am
Posts: 803
Location: Lost in the woods - somewhere...
Anyone ever replace one of these themselves? My driver's seat needs to have the track assembly replaced. (Dealer wanted >$500 to get part and do the work. I found the part on-line for half that.) Any suggestions would be appreciated. Thanks!

_________________
-Vicki-
'02 Renegade - "Forest Ops" Edition Locked, not stock and ready to roll.
ARB bumper, Super Skink Sliders, OME/Rancho lift, Treadwright Wardens 245/75/16, Skid Row engine skid, Mopar Skids, JBA 4.5 UCAs, 4.10s and Detroit lockers Coming soon: new winch, ?????


Top
 Profile  
 
 Post subject:
PostPosted: Mon Jul 09, 2007 2:49 pm 
Offline
Lifetime Member
Lifetime Member
User avatar

Joined: Fri Dec 30, 2005 11:50 am
Posts: 802
Location: 15 acres of goodness in Fleetville, PA
It should just be 4 bolts holding it to the floor

_________________
-oooooo- ---Craig, L.O.S.T. #CT068103
/______\ ---http://jeep.allgris.com
O||||||||O ---'02 Sport 4x4, 5-spd,
[]--------[] ---2.5" BDS lift, 245/75/16 MT/Rs, Moab Rims, Locked and Regeared!
[]_____[] ---The list got to long, go to my web site for more!


Top
 Profile  
 
 Post subject:
PostPosted: Mon Jul 09, 2007 3:59 pm 
Offline
Lifetime Member
Lifetime Member
User avatar

Joined: Tue Jan 24, 2006 1:44 pm
Posts: 249
Maybe it's just the '05's, but there are bolts on three corners (15mm socket) and the fourth corner goes onto a bolt sticking out of the floor. Either way it takes all of about 10 minutes to get a seat out of the jeep.

You'll also need a T-40 torx bit to get the seatbelt off the seat, its underneath the trim on the outside of the seat. Trim is all attached with phillips head screws, nothing fancy there. Its been a while since i swapped tracks, but i think there are a total of 8 bolts attaching the track to the seat. Three on each side and two in the back I don't think they all take the same socket tho, but they like everything else they are all metric.

_________________
'05 Sport
'92 Comanche Eliminator


Top
 Profile  
 
 Post subject:
PostPosted: Tue Jul 10, 2007 2:31 pm 
Offline
LOST Addict
User avatar

Joined: Thu Jul 07, 2005 5:32 pm
Posts: 1578
Location: Austin, Texas
I didn't need any Torx to remove the seat from the floor (seatbelt included). All I remember using was plain 15mm sockets I think. You need two sizes and one deep socket for removing the anchor bolt that's sticking up from the floor.

For my '03 I had to pop the seatbelt cover off the side, then use a deep 15mm socket to unbolt the belt from the seat.

The rear seats were fun to remove ...

_________________
DIRTY KJ :: flickr photostream
"Primitive life is very common and intelligent life is fairly rare ... some would say it has yet to occur on Earth" --- Stephen Hawking


Top
 Profile  
 
Display posts from previous:  Sort by  
Post new topic Reply to topic  [ 4 posts ] 

All times are UTC - 5 hours [ DST ]


Who is online

Users browsing this forum: No registered users and 6 guests


You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum

Search for:
Jump to:  
Powered by phpBB © 2000, 2002, 2005, 2007 phpBB Group. Color scheme by ColorizeIt!
Logo by pixeldecals.com