Dash Board Bezels

WoodysKJ · **Posted:** Sun Jul 15, 2007 3:02 pm

Anybody out there know the part number for the left side insturment panel bezel? I believe it is where the Roof Light switch is located. I am going to install some lights and want to locate the switch there. I have mine removed and it shows an area for the switch to be cut in.

Existing Part Number:

Switch location on inside:

Does anybody know how to tell from the many part numbers listed in the part sheet Which one is for a grey interoir and has this location already cut out ready to add the switch?

Anybody have one to sell?

Jeepjeepster · **Posted:** Sun Jul 15, 2007 4:10 pm

I caught one for free in the for sale section, I had the same thing in mind as you do. I have extra lights on the front and wanted it to appear stock from the inside.

My idea was kinda shot down when I looked at the price for the switch that goes in that hole! $30!!!!!! It has a relay and fuses in in one.. :shock:

jason thompson · **Posted:** Sun Jul 15, 2007 4:21 pm

what about a flush mount type swich and cut it with a dremel tool?
that is how I mounted the swiches for the ARB

WoodysKJ · **Posted:** Sun Jul 15, 2007 4:34 pm

Sounds good.

I need pics.

I am looking for a spare bezel so I can do the surgry needed and still have a fall back.

jeepjeepster, Pics of your switch?

tjkoen01 · **Posted:** Mon Jul 16, 2007 8:29 am

I shaved the factory switch mount off of the back of mine and got some chrome toggle switches from radio hut, drilled holes and presto! I opted for the RS switches b/c I wanted all my switches to match and needed a single pole, double throw with a center off.

WoodysKJ · **Posted:** Mon Jul 16, 2007 9:41 am

PICS PLEASE!!!!

CaKJFreedom · **Posted:** Mon Jul 16, 2007 12:28 pm

I just dremel'd mine too. Got a small switch from Auto Zone. Don't do it in the kitchen, there'll be plastic dust everywhere and you get in trouble.

WoodysKJ · **Posted:** Mon Jul 16, 2007 12:33 pm

Nanette,

Thats a COOL looking switch!!!!!!!!!! best one i have ever seen, where at AutoZone? it came with the beauty ring?

What is it rated? How many lights do you run off it and the relay?

I could see a few of those. VERY descreat and clean.

GREAT job!!!

pokefan · **Posted:** Mon Jul 16, 2007 12:34 pm

CaKJFreedom wrote:

Don't do it in the kitchen, there'll be plastic dust everywhere and you get in trouble.

X2

Quote:

I was going to post pics of mine but that's exactly how mine looks.

Jeepjeepster · **Posted:** Mon Jul 16, 2007 1:00 pm

Ive got the same switch but Ive yet to put it in. 5 bought mine at Advance auto parts for around $5 or so.

I dont have any pics of that woody..

Gris · **Posted:** Mon Jul 16, 2007 1:35 pm

I dremeled mine. Cheaper than buying a new one.

Maximum Carnage · **Posted:** Mon Jul 16, 2007 1:52 pm

CaKJFreedom wrote:

The same switch came with my Hella FF75. I too have a switch in this area.

CaKJFreedom · **Posted:** Wed Jul 18, 2007 12:48 pm

Glad I could save you a step pokefan. It's a cool little switch, just a couple bucks and yes, the ring is part of it. I love any reason to dremel....

I don't remember what it's rated. There's a relay and four lights work off of it.

riptricket · **Posted:** Wed Jul 18, 2007 3:11 pm

what accssory did you hook into your dremel to make such a clean circle?

pokefan · **Posted:** Wed Jul 18, 2007 6:29 pm

lol, My way was a little ghetto but I got a finishing buff and opened up the hole enough with a drill to get it in there and then just let it spin and open up the hole. Little primitive but it worked :lol:

CaKJFreedom · **Posted:** Thu Jul 19, 2007 7:30 pm

It's actually a Black and Decker generic Dremel. It has an attachment that's a circle about a half inch thick. Kind of like a stack of dimes that'll cut stuff. I marked the center, drilled it out, then just used the circle part until it was big enough. I'm anal about some stuff and that helped.

Dash Board Bezels

Who is online