J.C. Whitney is tempting me with the Sunpro Triple Gaugecage in the link below: http://www.jcwhitney.com/autoparts/Prod ... gauge+pods

Has anyone tried this to see if it fits? I would hate to buy it and find that I need to chop one of the mounting holes off to fit the pillar.

Steve

_________________
2006 Pearl Green CRD
Magnaflow 2 1/2" Cat Back
KJ Extra Leg Room Brackets, Carter Lift Pump, V6 Airbox, ORM
Fuel cooler, Oil Separator, Progard 7
Gauges EGT Boost Trans Temp Oil Pres, Michelin LXT AT2 245 70 R16
7,000# Draw Tight hitch, PML EX Deep Trans Pan
Centrifuge, SunCoast, Transgo, RAM TCM, InMotion Stage 2
Wife's 99 TDI VW Beetle

You have a pretty bad blind spot with a double gauge pod. If that's a triple, it's going to be huge. You can also buy the double pod for the Liberty here.

http://www.gaugepods.com/jeep.html

_________________
June 2001 Liberty Limited 4X4
Frankenlift II Premium, Al's Upper Arms, 245/75R16 C Silent Armors on Moabs, RL Skink Super Sliders, Rear DTT, Riddler Diff Cover, Fastman Throttle Body, Profinish-Proglass Hood, Borla Dual Outlet Exhaust, TransGo Reprogramming Kit, APS Stall Converter, 4.10 Gears, B&G Chrysler PCM, Lots of Line-X, etc...

not only that, but you also loose your one and only "oh my god" bar.

_________________
http://www.Colorado4Wheel.com
"Its not about what you can DO with your Jeep, its about where you can GO with your Jeep."
Knowledgeable - But Caustic

X2^

I'm replacing mine with the oh $%## handle. Just haven't finished pulling all the old N2O stuff. Now that it's lifted, it would really help with getting in and out. Plus, the blind spot is just too big. Very difficult to see while turning left.

_________________
June 2001 Liberty Limited 4X4
Frankenlift II Premium, Al's Upper Arms, 245/75R16 C Silent Armors on Moabs, RL Skink Super Sliders, Rear DTT, Riddler Diff Cover, Fastman Throttle Body, Profinish-Proglass Hood, Borla Dual Outlet Exhaust, TransGo Reprogramming Kit, APS Stall Converter, 4.10 Gears, B&G Chrysler PCM, Lots of Line-X, etc...

Yea, I wouldnt want to loose my ohh poo handle. I use it getting in and out and also while driving. I may be alittle more spirited than most drivers though.

_________________
LOST KJ'S
Where are you going???
Current Jeep: 2004 Jeep Liberty
-Atlantic Blue
-Air Ride Rear Suspension ; OME/Rustys Lift ; Powertrax Locker ; Moog Lower Ball-Joints ; 245/70/16 Yokohama Geolander A/T-S's on MOABS ; Flowmaster 50 SUV
Lost #007082
http://www.cardomain.com/id/jeepjeepster

Dude..... A universal fit? Come on!

_________________
My pics!!
'03 Rennie w/all Tupperware
Custom Roof Basket
Mopar Tubular Brush Guard
Garmin GPS V & Laptop w/Nav software
RAM products laptop mount
Maglite w/mount
Rear cargo bay tool cabinet
AllJs Rear Shelf
Rear receiver
250k miles!
LOST #CR051230

I have the lotech and like it. I never use the grab bar so no loss for me. I have no issues with the blind spot either. Dont know maybe i'm just used to it. I had 3 other cars with a pillar pods. Personal preference i guess. I wanted a couple gauges that the dash was lacking. If you're gonna get one get the lotech since it's molded for the kj not a jc whitney pos that'll make it look ghetto.

_________________
02' Sport- SOLD

07' Dodge Ram Quad Cab 1500 4x4
Yeah it's got a hemi!

I needed the gauges when it was setup as a sport truck. Way too dangerous to run a big shot of N2O without knowing your pressures. I just don't need it now, and the handle would be nice. If you want one, or need one, get the Lotech. Here's an example from the website I bought mine from.

_________________
June 2001 Liberty Limited 4X4
Frankenlift II Premium, Al's Upper Arms, 245/75R16 C Silent Armors on Moabs, RL Skink Super Sliders, Rear DTT, Riddler Diff Cover, Fastman Throttle Body, Profinish-Proglass Hood, Borla Dual Outlet Exhaust, TransGo Reprogramming Kit, APS Stall Converter, 4.10 Gears, B&G Chrysler PCM, Lots of Line-X, etc...