HOw has done it before on drivers side?

How much is the new CV and inner shaft for both sides?

is it easy but time worthy to do?

I think my drivers CV is hosed. After my front drive shaft was replaced the other day, I now developed a strange noise from the drivers side wheel. I can only hear it from inside of the rig and hear it most at 10 mph and lower. Stopping speeds and at take off.


You think its a CV?
I was under the KJ last night but i did not see anythig out of the ordinary. Took wheel off spun the rotor and did not really hear it but I suspect a little metal to metal sound. not 100% sure but it was something

_________________
2003 KJ Sport JEEPZILLA Edition
American Flag flying high
Frankenlift removed =(
Moabs and plenty of pin striping
Flexable people don't get bent out of shape!
Current MPG 6" to a gallon
L.O.S.T. # BL065211
www.ItAtYourHome.com

tech section

_________________
L.O.S.T. #225019
2003 Sport 4x4
Patriot Blue w/ trail rash
Flex-Zilla 4" Lift
TrailRash hi-lift mounts
Other stuff you wish you had

kool thanks man.

how long did it take you to do your drivers side?
And what prompted you to do it?

_________________
2003 KJ Sport JEEPZILLA Edition
American Flag flying high
Frankenlift removed =(
Moabs and plenty of pin striping
Flexable people don't get bent out of shape!
Current MPG 6" to a gallon
L.O.S.T. # BL065211
www.ItAtYourHome.com

my passenger side went bad REALY BAD , both cv & inner axel shaft got done due to they were fused together

so for $400 total problem fixed

the INNER SHAFT is a DEALER ONLY item, believe me the shop tried & made numerous calls but to no avail, the CV shaft came from NAPA, IT TOOK THEM 2HRS to get it all done....problem fixed

_________________
PETE
ADMINISTRATOR
L.O.S.T. 4 LIFE
04 COLUMBIA ED. & 04 SPORT

Be prepared to sacrifice a saturday to replace the front CV shaft if its your first time.

_________________
http://www.Colorado4Wheel.com
"Its not about what you can DO with your Jeep, its about where you can GO with your Jeep."
Knowledgeable - But Caustic

The time it took you to put just the front of the Frankinlift on,then add about 20min per side,is the lentgh of time to replace the CV shafts.About 2 hours for me,not hard at all,just kinda sucks you need to remove the strut/coil(makes it easier) and remove the knuckle completely.

Yea I was thinking the whole thing had to come apart. It will be like redoing my lift.


Hey tjkj2002

You seem to know a ton of CRAP here.
I was wondering, could it just be my wheel bearing going bad?
The noise I get is only from a slow start and a slow stop between 5-10mph and then again I will here a noise and a slight vibration at 60-75 mph.

When I turn the wheel both directions, I do not hear anything. No knocking, clicking, grinding.

_________________
2003 KJ Sport JEEPZILLA Edition
American Flag flying high
Frankenlift removed =(
Moabs and plenty of pin striping
Flexable people don't get bent out of shape!
Current MPG 6" to a gallon
L.O.S.T. # BL065211
www.ItAtYourHome.com

Jack the Jeep up and check for play in the bearings. I like to take the rotors off so I can turn the bearings by hand and feel them.

CV's will usually click alot when you turn.

_________________
LOST KJ'S
Where are you going???
Current Jeep: 2004 Jeep Liberty
-Atlantic Blue
-Air Ride Rear Suspension ; OME/Rustys Lift ; Powertrax Locker ; Moog Lower Ball-Joints ; 245/70/16 Yokohama Geolander A/T-S's on MOABS ; Flowmaster 50 SUV
Lost #007082
http://www.cardomain.com/id/jeepjeepster

I HAVE NO CLICKING WHATS SO EVER!

_________________
2003 KJ Sport JEEPZILLA Edition
American Flag flying high
Frankenlift removed =(
Moabs and plenty of pin striping
Flexable people don't get bent out of shape!
Current MPG 6" to a gallon
L.O.S.T. # BL065211
www.ItAtYourHome.com