Front Lights

jeepmedic46 · **Posted:** Wed Nov 12, 2008 2:58 pm

Been thinking about mounting a set of Kc daylighters on the front bumper. Its the stock bumper any suggestions on how to do this?

jeepkj02 · **Posted:** Wed Nov 12, 2008 3:27 pm

Check out this light bar. It is made for the Wrangler but Sport made it fit his 06 KJ.

http://www.lostjeeps.com/forum/phpBB3/vie ... hp?t=37218

jeepmedic46 · **Posted:** Wed Nov 12, 2008 5:41 pm

Thats a good idea, Thank you

Maximum Carnage · **Posted:** Wed Nov 12, 2008 6:53 pm

Looks like they are mounted directly on the bumper fascia, wouldn't that make them shaky when driving?

teckman02 · **Posted:** Wed Nov 12, 2008 6:59 pm

this is how i did mine

jeepmedic46 · **Posted:** Wed Nov 12, 2008 7:07 pm

Thats what I was thinking, How did you mount them? And where did you put the switches?

teckman02 · **Posted:** Wed Nov 12, 2008 7:52 pm

i took just drilled out the holes on the inside of the bumper i took some sheat metal that i had laying around, folded it over to have a good anchor since the bumper is all plastic. i fed the wiers through the back hole with some hard rubber tubing and heat shrink to keep everything water tight.

this is an existing ground on the left side of the firewall with the relay of the lights

this is some info that i found on how to get through the firewall http://en.wikibooks.org/wiki/Jeep_Liberty/Electrical/Firewall_Penetration

for the 12volt + i ran it off the 12volt+ from the daytime running lights

and the swich i put it on the center console

this weekend when a buddy of mine helps me fix my cv joint i will take some pics of behine the bumper
and oh yes make sure that you make sure that you mape some kind of disconnects so if you ever have to take off your bumper you don't have to rewire your lights each time you take off your bumper.... i learned that one the hard way when a buddy made my clevis mounts for me

jeepmedic46 · **Posted:** Wed Nov 12, 2008 8:44 pm

Thank you, Do you have any shaking on the lights?

teckman02 · **Posted:** Wed Nov 12, 2008 9:37 pm

icefisher45 wrote:

Thank you, Do you have any shaking on the lights?

i do just a little but not not much at all... i am guessing that the kj that is in your avatar is yours and your bumper looks a bit more solid than mine and two since i have takin that pic i have done some trimming and cuting down bumper for better clearance on the trail

kskj · **Posted:** Wed Nov 12, 2008 10:21 pm

On my 04 there is steel under the plastic skin mine don't vibrate at all. If you look at the bottom of the bumper there are two access holes one on each side. You can get a socket in to tighten the bolts holding on the lights. I made two small brackets to hold the lights so it would be easy to get to the bolts on the bottom side.

LIV42DY · **Posted:** Thu Nov 13, 2008 12:24 am

Try this one its been posted before. my cousin bent the tubbing for me, i did the rest, had my local body Shop match the paint.

jeepmedic46 · **Posted:** Thu Nov 13, 2008 7:09 am

Thank you, good ideas everybody

corwyyn · **Posted:** Thu Nov 13, 2008 7:52 am

kskj wrote:

On my 04 there is steel under the plastic skin mine don't vibrate at all. If you look at the bottom of the bumper there are two access holes one on each side. You can get a socket in to tighten the bolts holding on the lights. I made two small brackets to hold the lights so it would be easy to get to the bolts on the bottom side.

Good idea - I just drilled the bumper and ran the bolts for mine straight thru but they are a bit close to the grille for proper aiming. And yes the bumpers on the '05+ models do not have the same steel frame under them that the '02-'04 models do. I believe they use some small metal brackets mounted to a crossmember section for the Renegade-style lights on the bumper.

teckman02 wrote:

this is some info that i found on how to get through the firewall http://en.wikibooks.org/wiki/Jeep_Liberty/Electrical/Firewall_Penetration

Yep, that is some good info right there :wink:

Maximum Carnage · **Posted:** Thu Nov 13, 2008 9:21 am

teckman02 wrote:

Teckman02 where did you get this switch from?

jsc7002 · **Posted:** Thu Nov 13, 2008 1:32 pm

I think wal-mart carries them or ones very similar

ramlebliberty · **Posted:** Thu Nov 13, 2008 10:15 pm

Great ideas, I might do this next paycheck. My wife's going to give me an allowance starting next pay period *SWEET*

teckman02 · **Posted:** Thu Nov 13, 2008 11:54 pm

Maximum Carnage wrote:

teckman02 wrote:

Teckman02 where did you get this switch from?

the swich came in the kit with the hella 500's that i got

Front Lights

Who is online