SUPER 44

oddball · **Posted:** Sun May 03, 2009 10:43 am

Save the sand. Touch it up if you must and be done with it. Enjoy!

(I still need to install my 44OR).

riptricket · **Posted:** Sun May 03, 2009 11:20 am

alright got that solved...
Now, can I save the $40-50 and instead of welding it on just use some pipe clamps? or would it be better to spend the dough?

L.O. · **Posted:** Sun May 03, 2009 6:51 pm

just hacksaw a slot in the inlet and outlet pipes and use the clamps. Do it at home and save the bucks. Just tighten the clams well...I've never had one come loose.

JMSMN · **Posted:** Sun May 03, 2009 8:18 pm

I just put mine in. Cut off the 2 '' reduction in front and in rear of the muffler. Buy a piece of 18" 2 1/2" muffler pipe with a bell on one end, cut one inch off the piece of pipe, not the bell end. Put in place and clamp down tight. Worked great and is on really tight. Sounds great also. If you get the right piece of pipe, you dont have to cut any slots in the pipe.

riptricket · **Posted:** Sun May 03, 2009 11:41 pm

Alright!!!
and this is my 2000th POST!!!

riptricket · **Posted:** Mon May 04, 2009 11:21 am

JMSMN wrote:

I just put mine in. Cut off the 2 '' reduction in front and in rear of the muffler. Buy a piece of 18" 2 1/2" muffler pipe with a bell on one end, cut one inch off the piece of pipe, not the bell end. Put in place and clamp down tight. Worked great and is on really tight. Sounds great also. If you get the right piece of pipe, you dont have to cut any slots in the pipe.

Do you have pictures?

JMSMN · **Posted:** Tue May 05, 2009 5:15 pm

I can go out and snap some, but will have to wait for the wife to get home as I dont know how to put them up.

riptricket · **Posted:** Tue May 05, 2009 5:43 pm

THAT WOULD BE GREATLY APPRECIATED!

JMSMN · **Posted:** Tue May 05, 2009 10:13 pm

These are the pics I took tonight. On each end of the muffler, there is a 2" restriction, cut that off as close to it as possible. You dont have to cut a slot in the inlet and the outlet of the muffler, they are just slightly lartger than the 2 1/2" pipe so it slides over the exhaust nice and tight. On the pic of the new pipe, to the right of the sticker you can see the slight flare in the pipe to slide over the existing exhaust. You only need a one 18" piece of exhaust, with the flare on one end, and three 2 1/2" muffler clamps.

JMSMN · **Posted:** Tue May 05, 2009 10:14 pm

This is my first try with pics so I hope they work.

riptricket · **Posted:** Tue May 05, 2009 10:16 pm

[quote="JMSMN"]These are the pics I took tonight. On each end of the muffler, there is a 2" restriction, cut that off as close to it as possible. You dont have to cut a slot in the inlet and the outlet of the muffler, they are just slightly lartger than the 2 1/2" pipe so it slides over the exhaust nice and tight. On the pic of the new pipe, to the right of the sticker you can see the slight flare in the pipe to slide over the existing exhaust. You only need a one 18" piece of exhaust, with the flare on one end, and three 2 1/2" muffler clamps.

JMSMN · **Posted:** Tue May 05, 2009 10:19 pm

Why do they show up in your reply and not in my post?

riptricket · **Posted:** Tue May 05, 2009 10:19 pm

fixed your pics and thanks that really really helps!!!

JMSMN · **Posted:** Tue May 05, 2009 10:21 pm

What did you do?

DryBones · **Posted:** Tue May 05, 2009 10:25 pm

you need to make sure the "img" is in front of the link and the "/img" is at back for each photo.

riptricket · **Posted:** Tue May 05, 2009 10:29 pm

you hit the img button before you type in your pic then you hti it again to lock it in

riptricket · **Posted:** Tue May 05, 2009 10:30 pm

bigger.

JMSMN · **Posted:** Tue May 05, 2009 10:33 pm

Did I make those pics that size by accident?

JMSMN · **Posted:** Tue May 05, 2009 10:35 pm

Sorry for the gigantic pics, am getting better.

riptricket · **Posted:** Tue May 05, 2009 10:53 pm

JMSMN wrote:

Did I make those pics that size by accident?

no, i made them bigger!

SUPER 44

Who is online