What have you done to your KK lately

E2 · **Posted:** Mon Mar 08, 2010 3:23 am

DirtyKK wrote:

Diggerfreek wrote:

DirtyKK wrote:

i dont think adjusting the trackbar is gonna do anything... just gonna have to buy the tom woods driveshaft :twisted:

LOL a 1/2 inch adjustment will help tons :wink:

Just remember, 37.5 to 37.75 is the magic spot :mrgreen:

buy the drive shaft :mrgreen:

It sounded like my axle dropped when this happened! I was scared of what to expect, but could not see anything. I did this while driving to capture some pics for all of you of my flex, but never got that far. My dad came both of us went back and forth from under the truck and the driver seat back and forth in drive and reverse until my dad said it sounds like the drive shaft. I then checked it out and it shook when it happened. So this is what I saw! The drove back to my parents and was under the truck for the next 2 hours with tools! And still no flex shots..... Better here then off road!!! I need to increase my tools in my bag in the truck. No major right turns into driveways until I adjust my track bar. Also one of my weights fell off. Best part of the day was hanging out with my dad messing with the jeep.

Diggerfreek · **Posted:** Mon Mar 08, 2010 5:12 pm

Yeah, the noise is like :shock:

Elt31987 · **Posted:** Mon Mar 08, 2010 5:15 pm

Diggerfreek wrote:

Yeah, the noise is lie :shock:

So the Cake is a Noise then?

Diggerfreek · **Posted:** Mon Mar 08, 2010 5:36 pm

Elt31987 wrote:

Diggerfreek wrote:

Yeah, the noise is lie :shock:

So the Cake is a Noise then?

Say what

If only I could spell :banghead:

Elt31987 · **Posted:** Mon Mar 08, 2010 5:57 pm

Diggerfreek wrote:

Elt31987 wrote:

Diggerfreek wrote:

Yeah, the noise is lie :shock:

So the Cake is a Noise then?

Say what

If only I could spell :banghead:

lol sorry though you were making reference to the video game "Portal" where "The Cake is a Lie"

Diggerfreek · **Posted:** Mon Mar 08, 2010 6:07 pm

Elt31987 wrote:

Diggerfreek wrote:

Elt31987 wrote:

So the Cake is a Noise then?

Say what

If only I could spell :banghead:

lol sorry though you were making reference to the video game "Portal" where "The Cake is a Lie"

No worries :mrgreen:

clacker · **Posted:** Tue Mar 09, 2010 1:40 pm

Borrowed this from a thread over on JeepKJ: 2nd 12v socket

Finally mounted my CB radio and antenna:

Wnahikian · **Posted:** Tue Mar 09, 2010 6:03 pm

Just ordered some lights for a light bar, but check out the next viral internet sensation....
http://www.youtube.com/watch?v=EWpecs_Q5_c

Diggerfreek · **Posted:** Tue Mar 09, 2010 6:34 pm

Wnahikian wrote:

Just ordered some lights for a light bar, but check out the next viral internet sensation....
http://www.youtube.com/watch?v=EWpecs_Q5_c

Wnahikian · **Posted:** Tue Mar 09, 2010 6:40 pm

Ive had it on the lockdown for 2 years and finally time to release :BANANA:

Elt31987 · **Posted:** Tue Mar 09, 2010 7:25 pm

lol Digger, i think you should get some purple sweatpants like hers :lol:

Diggerfreek · **Posted:** Tue Mar 09, 2010 7:29 pm

Elt31987 wrote:

lol Digger, i think you should get some purple sweatpants like hers :lol:

I'm good.... I'm more of a shorts kinda guy :SOMBRERO:

Elt31987 · **Posted:** Thu Mar 11, 2010 8:58 pm

[quote="MtnLuvr"]Had the most enjoyable weekend day I've had in awhile this past Saturday. I got to spend it not working and spent it with my dad working on the Jeep:

First, installed a 3 D-cell LED Maglight below the driver's seat:

Do you think the 4 D-cell LED MagLite will fit? Its 2" longer than the 3 D. Thanks in Advance

MtnLuvr · **Posted:** Thu Mar 11, 2010 10:45 pm

Elt31987 wrote:

MtnLuvr wrote:

Had the most enjoyable weekend day I've had in awhile this past Saturday. I got to spend it not working and spent it with my dad working on the Jeep:

First, installed a 3 D-cell LED Maglight below the driver's seat:

Do you think the 4 D-cell LED MagLite will fit? Its 2" longer than the 3 D. Thanks in Advance

It would fit, but the back end (as I have mine oriented in the photo) will be a little beyond the curvature of the trim piece but I think you could still get it in and out (with the door open). Buy one and just hold it in place to check. That's how I figured out the 2 D-cell Maglight I had was too short to span across the seat mounting brackets. Good luck.

DirtyKK · **Posted:** Fri Mar 12, 2010 6:16 am

Picked up new rain-x wipers today. Pretty much two for the price of one anywhere else. The shopette on base had em scanned for the wrong price. :mrgreen:

DirtyKK · **Posted:** Fri Mar 12, 2010 9:49 am

changed spark plugs to some ngk iridiums also... maybe ill pick up some mpg's, idk the last time they were changed...

Wnahikian · **Posted:** Fri Mar 12, 2010 12:01 pm

Custom Light bar :BANANA:

Woop woop!

E2 · **Posted:** Sat Mar 13, 2010 6:44 pm

Tried on a 265/75r16 it fits. It turns with one finger clearance at two spots all other locations not bad.I'm sure it will rub slightly when flexing/compressing but not bad. I would have got them BUT YEAH BUT not sure about gearing. Auto with 3.73 stock and I do tow about 2200# from LA area to Laughlin, AZ. I few good hill climbs out of Laughlin that if I remember well with the stock tires I was some what max'd out at about 60 mph. Was not flooring it but if I did much much more noise but not much mpg so I just left it at about 60. My old truck with a 4.3 was about 55-65 but it was old and worried about over heating. The jeep not worried about that but I can't drive 55. I also stopped by ORU offroad unlimited the guy had to look twice at my truck. what? wow does not look like a liberty.... He told me about $825 in just labor to regear! plus parts. The 265/75r16 feel way off in the distance now....

Diggerfreek · **Posted:** Sun Mar 14, 2010 4:00 am

400 an axle isn't bad for labor. Takes like 8 hours to R and I the front diff IIRC

MtnLuvr · **Posted:** Sun Mar 14, 2010 9:53 am

Installed some PIAA 510 ATP lights on my front bumper:

What have you done to your KK lately

Who is online