is there a how to on jba arms... if not what tools do i need, people keep telling me i need this special fork thing???

_________________
08 Revenge- Rock Lizard (Skink Sliders & Gecko Roof Rails), High Clearance Trimmed Front Bumper, Mopar skids, Riddler Diff Cover, JBA (5.5 Arms, 6" rear Springs, Front Adjust-A-Struts), 32" DuraTracs, Superior 4.56's, Front & Rear ARB Lockers, Fastman Throttle Body, AEM Intake, Hypertech Tune, Custom Ram Air, RunCool Louvers

Nope, the Pass Side is easy, just remove the air box and remove the 2 bolts, the driver side bolt that is towards the front is also easy, the back drivers side bolt you will need an extension and a Universal connection to get a better angle then go in from the front of the Jeep rite where the front driver bolt is. I dont remember if you need to remove the battery. I can look after work and tell you

_________________
2008 KK Liberty
Inferno Red
Daystar 2" Spacer Lift With SkyJacker Hydro Shocks
JBA Gen 5.5 Upper Control Arms
Rokmen Riddler 8.25 Differential Cover
2 KC Slimlite 100 Watt Driving Lights on JK Light Bar
245/75/16 All Terrains
Mopar Front Tow Hooks
Mopar Rear Tow Hook
Mopar Skids

To pop the ball joint, just smack the part of the knuckle the ball joint goes in to to release it....

_________________
2008 KK Liberty Sport NIGHT OPS EDITION + GILLS
OEM & Custom Skids - Factory Tow Package - Rock Lizard Skink Super Sliders
Prototype JBA 4 Inch Lift - JBA UCA's - Flowmaster Super 44 OR - Whacked Resonator
Jet Stage 2 - RL Gecko Basket Rack - Custom Winch Bumper - Recon 10.5K Winch

so i attemtper this today but failed.... that rear driver side bolt is a real pain... i figured id start there... good thing too... i cant figure out how to get the socket on it and have enough room to actually turn the ratchet... i can get the socket on it but i never have any room to really move the ratchet... i feel like the steering rack or abs pump are in the way.... any suggestions or explanations on what to do... even pics would help... anything really lol

_________________
08 Revenge- Rock Lizard (Skink Sliders & Gecko Roof Rails), High Clearance Trimmed Front Bumper, Mopar skids, Riddler Diff Cover, JBA (5.5 Arms, 6" rear Springs, Front Adjust-A-Struts), 32" DuraTracs, Superior 4.56's, Front & Rear ARB Lockers, Fastman Throttle Body, AEM Intake, Hypertech Tune, Custom Ram Air, RunCool Louvers

as a note i had both the fuse box and the battery/tray out

_________________
08 Revenge- Rock Lizard (Skink Sliders & Gecko Roof Rails), High Clearance Trimmed Front Bumper, Mopar skids, Riddler Diff Cover, JBA (5.5 Arms, 6" rear Springs, Front Adjust-A-Struts), 32" DuraTracs, Superior 4.56's, Front & Rear ARB Lockers, Fastman Throttle Body, AEM Intake, Hypertech Tune, Custom Ram Air, RunCool Louvers

I used an Air Ratchet but there was still VERY LITTLE room to actually manually crank it.

_________________
2008 KK Liberty
Inferno Red
Daystar 2" Spacer Lift With SkyJacker Hydro Shocks
JBA Gen 5.5 Upper Control Arms
Rokmen Riddler 8.25 Differential Cover
2 KC Slimlite 100 Watt Driving Lights on JK Light Bar
245/75/16 All Terrains
Mopar Front Tow Hooks
Mopar Rear Tow Hook
Mopar Skids

U-joint and a long extension is how I did mine. It was still a PIA, but it worked.

_________________
07 KA Light Khaki, Manual trany.
2.5" Adjust-A-Strut JBA lift, Euro taillights,
Home made; Front Tilt Hood, Roof Rack, RAM Air, & CAI.
ESP Off Switch
Take a ride on the Trō side!

yeah air ratchet may be the way to go... i didnt even think of that ( and i have one too) stupid me

_________________
08 Revenge- Rock Lizard (Skink Sliders & Gecko Roof Rails), High Clearance Trimmed Front Bumper, Mopar skids, Riddler Diff Cover, JBA (5.5 Arms, 6" rear Springs, Front Adjust-A-Struts), 32" DuraTracs, Superior 4.56's, Front & Rear ARB Lockers, Fastman Throttle Body, AEM Intake, Hypertech Tune, Custom Ram Air, RunCool Louvers