Ok. the 4x4 libby vs the 2wd libby. There has to be a few more fire wall plugs on the 4x4 model for running the 4x4 stuff. I want to run a power line from the batt to inside the cab. lets say about around as a pinky finger. Were is the best place to run though a power line this big that will not mess up other electronics with a power line so close to them. hmm or is it just drill the wall, run the line and gasket goop the hole?

_________________
Honor, Justice, Liberty, Truth. Deed's not word's

There are already two plugged up openings in the firewall. I popped out the plastic part, put the wires through, then stuffed a whole bunch of silicon or clear RTV in the hole with the wires. Still going strong about two years later.
This should help a bit.
http://en.wikibooks.org/wiki/Jeep_Liber ... enetration

_________________
-dbk
SOLD2007 6 Speed - Projector Retrofit -Custom LED Tail Lights - Lights on Cowl & 130w 8" ProComps - Full Skids-RockLizard Super Skink Sliders-Front Hitch
Frankenlifted-Al's A-Arms-Goodyear Duractracs 31x10.5R15x7 Cragar D Window 4"bs-Cobra 75WXST - 4' Firestick
4.10s sitting in a box - 3
Sold-1988 Suzuki Samurai
2002 Jeep TJ

What do you need to run large power wires into the cab for?? Not a good idea. Use relays and keep the power on the other side of the firewall!

_________________
Civilisation exists by geological consent, subject to change without notice. -Durant

an amp?

_________________
2016 Cherokee Latitude

(SOLD) 2005 Liberty Renegade 4x4
2.5" Lift, Wrangler MT/R 245/75/16, Hella 500s, Black Widow Roof Rack, Stock Rock Rails, TJ Front Bumper, Flowmaster 44 Offroad

(SOLD) 2006 Liberty Limited 4x4
L.O.S.T. Stickers, Yokohama Geolander AT-S

Just drill a hole where you need it and install a rubber gromment with a little bit of clear silicone. The silicone will keep the gromment from coming out and also protect the metal edges from rusting.

You can buy rubber grommets from nearly any auto parts retailers Or....http://www.amazon.com/Mr-Gasket-3706-Gr ... B000934LBC

_________________
2003 Liberty Limited Edition

2006 Liberty Sport

That statement is confusing.

I drilled a hole in the blank where the clutch pedal would go through if it were manual. If there is a rubber grommet filling a hole it's best to leave it in place, cut a small X in it and push the wire through.

Not sure why a 2WD or a 4WD would have any more or less holes in the firewall compared to each other. Since you have the Jeep in front of you, you would know better than us. Have a look and if there are none, drill out a hole, put a snap-in plastic grommet in place and seal with silicone after the wire is run.

Probably should be in electrical section.

_________________
2006 CRD http://www.UtahPowderCoatings.com/ http://www.gorecon.com/ I'm kind of a big deal.
RL rear bumper, ARB front bumper, Mile Marker winch, Power Tank, Skids by Mopar & Skid Row, RL Super Skink Sliders, 235/85R16 MTR, Air Flow Snorkel, DTT, 4.10 gears, Frankenlift II, Katskin leather, JL Audio stereo, Rosen video.

You can take a hanger and unfold it,bend the tip over,and tape it.
Push this through the firewall plug under the master cylinder(from the inside undeneath above and to the left of the brake pedal).Attach wire,and pull it in.
This should work for one or two wires,my #2awg wires I had to hand drill a hole on top of the rubber grommet to get it through.Top'd it off with some rtv.

_________________
Bub
06 Inop Edition CRD Silver
06 Inop Edition CRD Green

That is incredibly helpful! Thanks for posting it.