rocker panels

irollgen4s · **Posted:** Tue Jul 26, 2011 7:55 pm

where can i buy the clips/push pins for this? they all broke today after taken them off for my JCR sliders(which fit like $#!^. will explain more if anyones curious).

arengant · **Posted:** Tue Jul 26, 2011 8:33 pm

Dealer, got some like 5 bucks a piece for the upper, the lower ones are hide to find (don't really need them??)

I'd have to dig for the part number, but when I went to parts counter they had them!

tommudd · **Posted:** Tue Jul 26, 2011 8:43 pm

You know you could of installed them without taking the covers off right?
We've done two sets here at my place and never removed them
They do need some revisions which we suggested to them but..........

irollgen4s · **Posted:** Tue Jul 26, 2011 11:13 pm

we could have, but it was just easier to rip em off. way easier to line them up and drill into the pinch seam. Any parts number/ proper name of the actual clips would be greatly appreciated!

CIMARRON13 · **Posted:** Wed Jul 27, 2011 1:12 am

All mine broke off as well. I usually throw all plastic away if it doesn't serve a purpose anyway. I am curious to hear how yours fit. Mine fit okay once I got them lined up. Called and emailed them to get directions for the KJ. I only had XJ directions from their website. Never heard back. Lost a few bolts because they just threw them in the huge box which UPS ripped to shreds before delivery.

irollgen4s · **Posted:** Wed Jul 27, 2011 10:55 am

Ill grab pictures of how we rigged it up today, i kid you not, it was 3/4 an inch short in back and half an inch in front. it was ridiculous.

irollgen4s · **Posted:** Wed Jul 27, 2011 12:21 pm

this is the rear drivers side

front drivers side

and it was exactly the same on the passenger side, maybe a little worse.

but they do look awesome

oh and theyre hold on by 3 bolts at each because there is a factory hole in the frame that we couldnt figure out how to put the 4th there.

tommudd · **Posted:** Wed Jul 27, 2011 12:28 pm

If you would of put the mounting bracket inside of the pinch weld they would of bolted up.
Thats the way we did both sets up here.
Now the hole in the frame we told them about it they need to have a longer bracket or something, We made a spacial plate and slipped it in the hole to bolt to. Regardless they do need to refab part of them

ABQKJ · **Posted:** Wed Jul 27, 2011 12:44 pm

I emailed for KJ directions and they replied that they mount the same as an XJ. However, as you can see, the XJ mounting method does not work. Like Tom said they mount to the inside of the pinch weld. They do have some pictures on the website that are informative.

CIMARRON13 · **Posted:** Wed Jul 27, 2011 5:05 pm

Mine fit, barely, using all bolts away from the frame hole. Unlike the directions I found it easier to use a right angle drill and drill holes while the sliders were installed rather than mark, remove and drill. This after thinking I was doing something wrong since the directions stated using a nut to line them up. I won't buy from them again since I never got a reply asking for intructions. Customer service goes a long way with me.

arengant · **Posted:** Wed Jul 27, 2011 9:06 pm

irollgen4s wrote:

we could have, but it was just easier to rip em off. way easier to line them up and drill into the pinch seam. Any parts number/ proper name of the actual clips would be greatly appreciated!

Sorry, I couldn't find my spare with the receipt, so no part number.

It was a body molding clip, but the uppers are grey not white like my old ones. They were NOT an exact fit, but they looked the same, and I got them to work just fine. 3.50 a piece, not five

irollgen4s · **Posted:** Wed Jul 27, 2011 11:27 pm

regardless there would have been a space, aka im disappointed in their product.

BugginKJ · **Joined:** Mon Jul 06, 2009 7:35 pm **Posts:** 4576

Mine fit like a glove, with the exception of the hole we had to deal with like Tom already said also Mr. Cool Ray Ed from Ohio also was the other install myself and Tom were personally involved with and if I recall his went in with out a snag and also fit like a glove. Plus the added bonus of looking dang good

irollgen4s · **Posted:** Thu Jul 28, 2011 1:36 pm

Even if we put the sliders on the inside of the seam they still would've been a massive gap that shouldn't be in any product, let alone an expensive and important one that protects our rigs.

AZ CRD · **Posted:** Mon Aug 01, 2011 6:38 pm

Mine, too, fit like gloves. I also used the method someone else said about drilling the holes with a right angle drill with the sliders in place. Worked great. And, yes, one of the bolt locations did line up with a factory hole so they're bolted up with one less bolt per side. Doubt it will make any difference.

I like 'em. Sturdy. Nice welds.

BugginKJ · **Joined:** Mon Jul 06, 2009 7:35 pm **Posts:** 4576

AZ CRD wrote:

Mine, too, fit like gloves. I also used the method someone else said about drilling the holes with a right angle drill with the sliders in place. Worked great. And, yes, one of the bolt locations did line up with a factory hole so they're bolted up with one less bolt per side. Doubt it will make any difference.

I like 'em. Sturdy. Nice welds.

Use the plate idea I used on mine, it worked perfect.

rocker panels

Who is online