So, I installed a brake controller in my Jeep and now I have some electrical issues. The controller has 4 wires, a +,-, and a brake light signal from the brake pedal. The remaining wire is what I thought I needed to tie into my harness by the hood release, the white wire with blue stripe. I did not cut this wire, but simply tied in the wire from the controller to it. Now when I hit the brakes my headlights come on! Not full on, and not all the time, but clearly something is wrong. Was I supposed to cut that wire and only tie to one side of it? Or am I way off and need a different wire?

_________________
2005 limited, tinted, OME lift, falken wildpeak 245/75-16, Suncoast, Transgo, Chevy fan+clutch, 195° Kap Stat Mod, Derale tranny cooler, Provent, Stage 2 tune, EGRdelete, Cat delete, Group65 batt, V6 airbox, tow brakes, switchblade key, DIY roof rack, DIY Front bumper,
Future; rear bumper, true tracs, tank fuel pump, webasto heater, 5sp manual

The brake signal wire by the hood release should not be hooked up to anything on one end. Should just be dangling there behind the trim panel. My wire was blue...not white with a blue stripe....2006 CRD. 2005 might be different.

Sent from my SM-G965W using Tapatalk

_________________
2006 Liberty CRD Limited

Provent @ 43,000 km
SEGR in progress
SAMCO Sport hoses @ 48500 km
Goodyear Wrangler Duratrac LT225/75R16

i am pretty sure my wire was blue also on a 2005 but I also think it had a label on it that said brake or something of that nature.

_________________
05 Blu LIM, OME GDE Tbo, wk II 245/75/17, KC Lights, bull bar, 195K H TC
05 Blu Lim, Dayton, GDE HT, 255/75/18 , 210K , H TC
06 Bla Lim, GDE Eco, Destination AT 245/75/17, 151K, H TC
06 D Khaki Lim 126K wkII Eur TC
05 D khaki Lim 145k refurbishing
All CRDS: Fumoto, Lift , Fan Shroud mod, fuel head Gen II, SAMCOS,self TB, 2 Mic filt, Hayden

Pretty sure mine also had a label....

Sent from my SM-G965W using Tapatalk

_________________
2006 Liberty CRD Limited

Provent @ 43,000 km
SEGR in progress
SAMCO Sport hoses @ 48500 km
Goodyear Wrangler Duratrac LT225/75R16

I looked all over for a loose wire. Well clearly I’ve tapped the wrong one. Back to the drawing board.

_________________
2005 limited, tinted, OME lift, falken wildpeak 245/75-16, Suncoast, Transgo, Chevy fan+clutch, 195° Kap Stat Mod, Derale tranny cooler, Provent, Stage 2 tune, EGRdelete, Cat delete, Group65 batt, V6 airbox, tow brakes, switchblade key, DIY roof rack, DIY Front bumper,
Future; rear bumper, true tracs, tank fuel pump, webasto heater, 5sp manual

Okay finally found it. Man, I’d like to strangle whoever designed the plastic wiring tray cover. Also, my wire was red not blue. But, I’m good and rant over, thanks for the help.

_________________
2005 limited, tinted, OME lift, falken wildpeak 245/75-16, Suncoast, Transgo, Chevy fan+clutch, 195° Kap Stat Mod, Derale tranny cooler, Provent, Stage 2 tune, EGRdelete, Cat delete, Group65 batt, V6 airbox, tow brakes, switchblade key, DIY roof rack, DIY Front bumper,
Future; rear bumper, true tracs, tank fuel pump, webasto heater, 5sp manual

just suggestion. Set up a signature with at least the model year of the Jeep and Sate of residence.

_________________
05 Blu LIM, OME GDE Tbo, wk II 245/75/17, KC Lights, bull bar, 195K H TC
05 Blu Lim, Dayton, GDE HT, 255/75/18 , 210K , H TC
06 Bla Lim, GDE Eco, Destination AT 245/75/17, 151K, H TC
06 D Khaki Lim 126K wkII Eur TC
05 D khaki Lim 145k refurbishing
All CRDS: Fumoto, Lift , Fan Shroud mod, fuel head Gen II, SAMCOS,self TB, 2 Mic filt, Hayden

X2, it helps others when trying to help you.

_________________
Supporting Vendor and Moderator of LOST
05 Jeep Liberty CRD Limited
Ironman Springs/Bilstein/Shocks
Yeti StgIV Hot Tune
Week's BatteryTray
No FCV/EGR
Samcos/ProVent
SunCoast/Transgo
Carter Intank-pmp
2mic.Sec.Fuel Filter
Flowmaster/NO CAT
V6Airbox/noVH
GM11 Bld.fan/HDClutch
IronrockArms/wwdieselMount
98 Dodge Cummins 24 Valve