installed the euro t/c and new flex plate....in my dirt drive way.
so far all's well , no chatter shifing into 5th ....
yay me!

_________________
2006 liberty crd black-n grey ero tc
1995 dodge ram 2500 cummins
1985 ford f-600 8.2l detroit diesel
2005 challenger mt-295 tractor

Nicely done!

_________________
05CRD: GDE Hot ECU & TCM tunes, Provent, Cat filter, Facet lift pump, TransGo kit, Florida TC, Samcos, stainless brake lines, HDS thermostat, Renegade light bar,
Bilstein adjustables, Al's Gen 4.5 Arms, 235/85-16 Duratracs, DTT rear, Elocker front, EVIC+TPMS, Turbo timer, McNally pillar gauges, Weeks Stage II kit.

Ah yes, the transmission pull, one of the rites of passage of CRD ownership.

_________________
http://www.Colorado4Wheel.com
"Its not about what you can DO with your Jeep, its about where you can GO with your Jeep."
Knowledgeable - But Caustic

Happy for you, did the same on mine (minus the flex) and no problemo ever since...

_________________
RIP 10/31/2012
Green Metallic 2006 CRD Limited
GDE Hot tune ~ Pre-F37 TCM ~ Transgo shift kit ~ MagnaFlow ~ Homemade Provent ~ OME 2" lift & Airlift ~ Samco ~ Euro TC ~ Lift pump ~ Nylon fan blade & Hayden clutch ~ Etc!

Good job Manuel

_________________
20 year owner of Libby CRD!
2006 LTD Bright Silver loaded with all the needed mods, CCV intact.
Equipped with HDS thermostat, plenty of heat, faster warm-ups, increased fuel mileage.

how many hours did it take you?

_________________
05 CRD Limited, SEGR Kit, EHM, Selectrack Alpine DVD, 6000k HID headlights, Aux Lift Pump, 2.5" straight pipe, Diablo Extreme Puck, Euro converter
02 SLT Cummins H.O. 6spd manual with southbend 3850dd, fass 150hd, ddp 150hp injectors, arp studs, adrenaline stacked w smarty, traction bars, 6 inch stacks, level kit, bhaf

it took me 1.5 hrs out and 2.5 hrs in .... on my back on a piece of plywood on my dirt driveway. oh yeah , i'm 6'4" and not what one would call dainty ....
they dont make these for big people!
i put 145 miles on it today and still good....
and ..... the CEL is not on
i had the EGR low flow/ underboost code for like 4 months
i did a fuel filter change and primed the filter with 911 fuel additive ...i think that desolved the crud and opened up the ports like prime-a-teen mist

_________________
2006 liberty crd black-n grey ero tc
1995 dodge ram 2500 cummins
1985 ford f-600 8.2l detroit diesel
2005 challenger mt-295 tractor

it took me longer than that to take entire intake and throttle body off and clean all the soot out. maybe i can handle it on my own, but im putting it on a lift at a buddys shop and doing it

_________________
05 CRD Limited, SEGR Kit, EHM, Selectrack Alpine DVD, 6000k HID headlights, Aux Lift Pump, 2.5" straight pipe, Diablo Extreme Puck, Euro converter
02 SLT Cummins H.O. 6spd manual with southbend 3850dd, fass 150hd, ddp 150hp injectors, arp studs, adrenaline stacked w smarty, traction bars, 6 inch stacks, level kit, bhaf

manuel before you replaced your stock T/C when you were idling did you notice a ticking sound? does that mean i probably need to replace my flex plate as well?

_________________
05 CRD Limited, SEGR Kit, EHM, Selectrack Alpine DVD, 6000k HID headlights, Aux Lift Pump, 2.5" straight pipe, Diablo Extreme Puck, Euro converter
02 SLT Cummins H.O. 6spd manual with southbend 3850dd, fass 150hd, ddp 150hp injectors, arp studs, adrenaline stacked w smarty, traction bars, 6 inch stacks, level kit, bhaf

yes ... replace it at once! just kidding
mine started out a slight tick then over the coarse of a week turned into a knock then would not drive....it was quick!

_________________
2006 liberty crd black-n grey ero tc
1995 dodge ram 2500 cummins
1985 ford f-600 8.2l detroit diesel
2005 challenger mt-295 tractor

o fantastic, mine has been ticking for at least 2 weeks now since i started noticing it, do you know the part number for the flex plate?

_________________
05 CRD Limited, SEGR Kit, EHM, Selectrack Alpine DVD, 6000k HID headlights, Aux Lift Pump, 2.5" straight pipe, Diablo Extreme Puck, Euro converter
02 SLT Cummins H.O. 6spd manual with southbend 3850dd, fass 150hd, ddp 150hp injectors, arp studs, adrenaline stacked w smarty, traction bars, 6 inch stacks, level kit, bhaf

sorry dont know part# but ordered from dealer , check the mopar parts website too.
i'd inspect the bolts that hold the torque converter to the flex plate ....i felt the need to pull the starter and ft drive shaft, but one guy said that you could pull the rubber inspection cover just above the starter....

_________________
2006 liberty crd black-n grey ero tc
1995 dodge ram 2500 cummins
1985 ford f-600 8.2l detroit diesel
2005 challenger mt-295 tractor